02-03-2011 12:38 PM - edited 07-03-2021 07:46 PM
Is there a way to configure an SNMP string on a lightweight access point (LWAPP)? WCS is running version 7.0.164.3. The 4402 controller is running version 7.0.98.0. The LWAPP is using image version 7.0.98.0. I can access the LWAPP using SSH and get to the enable prompt. Below are the commands I'm using.
AP01>ena
Password:
AP01#conf t
Enter configuration commands, one per line. End with CNTL/Z.
AP01(config)#snmp-server community mycomm ro
AP01(config)#exi
AP01#wr
Building configuration...
[OK]
NVRAM Verification Failed
AP01#
If there is a way to add the SNMP community from the controller or WCS, please let me know.
Thanks,
Tim
Solved! Go to Solution.
02-03-2011 11:14 PM
Hi,
ok.. Please correct me if my understanding are correct.. "You would like to poll LWAPP Via SNMP"?? is this right??
If So.
You cannot poll the APs directly, but will be able to get AP statistics by polling the WLC.
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull
02-03-2011 05:39 PM
Do u need the SNMP config on the WLC and WCS?? or the MIBS on the AP??
Regards
Surendra
02-03-2011 10:31 PM
I have SNMP community strings on WCS and WLC, but I want a RO string on the AP. I would like to be able to query the AP with a SNMP monitoring software (i.e. Solarwinds).
02-03-2011 11:14 PM
Hi,
ok.. Please correct me if my understanding are correct.. "You would like to poll LWAPP Via SNMP"?? is this right??
If So.
You cannot poll the APs directly, but will be able to get AP statistics by polling the WLC.
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull
02-10-2015 11:16 AM
Hi Sirbg
can you please let us know how to ....
''You cannot poll the APs directly, but will be able to get AP statistics by polling the WLC ''
What configuration is required in the Monitoring Software and WLCs. I am using OPNET VNE Server
02-10-2015 09:53 PM
Add your OPNET VNE Server as a trap receiver on the WLC under SNMP settings
once added try to poll the way u normally poll from any server to the WLC IP with the OID of the MIbs and it should work fine
06-24-2018 01:25 AM
Hello Dear,
I have added the WLC in the same way with SNMP but LAPs are coming in Solar Winds as "unknown" device.
I am not able to get any data about APs, (inventory, image, etc.)
Do you have another way to get it done?
Thanks,
Bilal
12-30-2011 11:22 AM
Tim,
I'm curious if you ever managed to get your LWAPPS configured with SNMP to be queried by monitoring software. I am currently setting up Solarwinds Orion and would be great to get visibility of my Cisco WLAN this way.
Regards,
Jon
12-30-2011 11:25 AM
Nope we cannot directly do anything on the LWAPP. its VIA the WLC
01-24-2018 06:55 AM
Hi man
usually when u poll some IP on some OID u know what's it about, this is not the case for this tread. could u pls share reference with MIB?
01-04-2012 09:33 AM
I was never able to get it working. I can only do a ping monitor from Solarwinds/Whats Up.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: