Hi all,I´m trying to set up in a lab enviroment in eve-ng, xr router and we have installed ios-xr 7.2.2 xrv9k image because we need to test few things including L2VPN and pw-ether termination but I can´t figure out for the life of me how I activate o...
Forum Posts
hello.I am using PRTG to monitor router ASR9910.The SNMP interface sensor traffic graph appears zigzagging.The scan interval is also set to 1 minute.I heard that some people solved the problem with ifmib cache, so I applied it, but the graph remains ...
Resolved! BGP Flowspec ASR9901 support
Hello all, I have a question, have someone tested the BGP flowspec client on ASR9901 ? It's IOS XR 7.1.3.I am correctly receiving FS prefix from remote FS controller but it is not programmed to hardwareRP/0/RSP0/CPU0:asr9901#show bgp ipv4 flowspecNet...
Resolved! Show alarms on 64-bit eXR for ASR 9000
Hello,In 32-bit Classic IOS XR, one could easily view the status of craft interface LEDs (e.g. alarm lights on RPs and front panel, etc) by running the "admin show environment leds" command. However, this command is no longer supported for ASR 9K pla...
Hi, as per the title, after we upgrade a NCS5508 to 7.7.21 from 7.3.2, the standby RP can no longer be utilised, it goes in a boot loop.What I've observed is the following: The RP can bake the XR image successfully however at the end I see this in th...
All, I have a simple route-policy I'd like to apply to a set of peers.This would be applied to 25k prefixes in the bgp table.Given no ios-regex is being used in the route-policy, I'm looking for any expertise on potential impact/load on the system. I...
Resolved! accessing admin exec mode
Hi all, I am having a problem to access the admin exec mode of an asr 9000 which runs 6.5.When I give the admin in exec mode it transfers me to RP/0/RSP1/CPU0:x1#adminadmin connected from 127.0.0.1 using console on x1sysadmin-vm:0_RSP0# exit Thanks i...
Hello,I am implementing flowspec on an NCS 5500, I accept the rules through eBGP. I am having problems because although I receive the routes correctly and I see that the TCAM has entries. The problem is that I am observing that the entries are not ha...
Hello Team,I have shared the OID details below with the customer for both the NCS and ASR9k platforms to retrieve the device serial number (chassis). However, despite attempting to use these OIDs, the customer is still unable to retrieve the serial n...
If I have an ASR 9910 with no FCs only two RSPs (A99-RSP-SE), what is the maximum Per Slot Fabric I can get?
I have an issue with one of our ncs 540 ios-xr devices. Somehow the HDD is coming up as locked which was not intended. I have tried booting the USB recovery, but everything stops at HDD is locked, then a scrambled blue screen shows up. Does anyone ...
hello everyone,I have a problem like thisWe will move from mikrotik to cisco asr9k bng,I made all the configs to run it as pppoe bras on the bng side, butNo PADI, etc. in debug aaa, radius, ppp, pppoe logs. information is not comingI connected the mo...
Hi, When I try to update NCS, I get the following errors: RP/0/RP0/CPU0:ios#install package replace /harddisk:/ncs540l-x64-7.7.21.iso synchronousFri Mar 1 11:28:51.176 UTCStarting:install package replace /harddisk:/ncs540l-x64-7.7.21.isoPackaging ope...
Hi All, im trying to install IOS XR on an NCS 540 acc sys, but evertime when i do the install add i get an error. First it was on the MD5 string, and now it is just failed. See the Install log below.i also checked the MD5 string, and that is just the...
Hello,I have an asr 9001 chassis with a module A9K-MPA-8X10GE but its status is not allow online 0/0/0 A9K-MPA-8X10GE NOT ALLOW ONLIN PWR,NSHUT,MON Does it need a license to activate or is not supported? Thank you,
