Hello, I just migrated from an ASR9001 with 6.3.3 to a NCS-57C3 with 7.7.2, Config is almost the same and everything is working as it should.I have 4 BVI interfaces, which i know for a fact are moving data, are reporting on 3 of my SNMP servers that...
Hello Dearsi cant add new route-policy for N540-24Z8Q2C-M like below:interface TenGigE0/0/0/8.363 l2transportservice-policy input TEST!!% 'DPA_QOSEA' detected the 'warning' condition 'Out of Resource'can you help me to solve this issue ?many thank...
Hi All,we have 5501 running 712 version with bridge-domain. Whenever AC flaps, local MAC learning takes ~30sec. Is there any known issueLC/0/0/CPU0:Feb 21 06:43:48.801 UTC: ifmgr[323]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGi...
Hello I have running ios xr and trying to set up a as-path prepending. What i have is our as and a few down stream bgp sessions. Trouble i am facing is that when i prepend my own as then all the other downstream bgp session drop traffic. Thanks f...
Hello team,We are encountering an issue with the 100G TR card on the ASR9K, which presents complications wherein shutting down one of the 100G ports resulted in an automatic shutdown of both 100 ports. If fiber connection is disconnected from the fir...
Hello everyone,I have a A9K-4X100GE-TR that has problems with the N. is there anybody has same experience and have any idea. RP/0/RSP0/CPU0:February(admin)#sh platformThu Feb 15 15:49:05.009 UTCNode Type State Config State----------------------------...
Hi,I can try to configure asr 9006 for bgp but I always see bgp neigbours idle. My configrations and asr logs are below. What can I do? Could you advice me please. ASR 9006 Router Config:!route-policy Accept-All pass end-policy!router bgp 100 bgp r...
I am fully aware that there are 2 versions of the 9001. 9001-S and 9001.Both 9001 and 9001-S have 4 built in SFP+ ports and BAY 0 and BAY 1.9001-S by default has BAY 0 active and SFP+ ports 0 & 1 active and requires a license to activate BAY 1 and S...
I am preparing router specification for upcoming projects and unable to find following parameters related to NCS540 routers in the cisco datasheets.Max nos. of Active Route Table (FIB) IPv4 prefixes and IPv6 prefixes.Max nos. of routing table (RIB) f...
Hi,I want to reenable an older ASR Satellite, but all I get is "no Identification received yet" and a reboot every 30 minutes.Other satellites (with newer software) are working fine.Here is my ASR output and config (IOS cXR 6.6.3):sh nv sat statuSate...
Hi All, I am trying to boot up an IOS XRv 9k 7.4.2 in eve-ng but its not booting, it rebooted in the first 2-3 minutes and afterwards its doing nothing, i can see the following message on the console but its not progressing any further. any idea pl...
Hi,in our network we're using the A9k-48x10-1G-SE LC on our ASR 9k deployment (running eXR 7.3.2), these boards have huge (in the thousands) l2transports interfaces configured on them and, most of these, have a service-policy associated.
Is it possib...
Hi dears , we have a Cisco ISR 4331 with software version Fuji 16.8.1 , which have known vulnerabilities.we want to patch theses vulnerabilitieswhich version should we move to ? and what is the upgrade path?thank you in advice.