Does anyone know exactly what memory is the L2-overwrite including MPLS labels stored on please?
And what is the max MPLS label limit for ASR9K's Typhoon and Tomahawk LCs please? (might RSP or a version of code be a limiting factor in available labe...
Hi all! Does anyone know an easy and quick way to show the installed Service Pack level on IOS XR for the NCS platform? I know I can compare the packages within the Service Pack TAR archive file and the output of the command: "(admin) show install ac...
Hi all!
Does anyone know, which IOS-XR release will support BGP l2vpn evpn AF over IPv6?
This is seen on IOS-XRv 6.5.1:
RP/0/RP0/CPU0:XR1(config)#router bgp 65000
RP/0/RP0/CPU0:XR1(config-bgp)#neighbor fc::2
RP/0/RP0/CPU0:XR1(config-bgp-nbr)#address-...
On ASR-9904 Chassis with RSP5-SE. I was under the impression that the RSP - Chassis combo could support 1.8T per line card. However, when a A9K-8X100GE-TR is inserted, I get RATE LIMITED message. %FABRIC-FIA-1-RATE_LIMITER_ON : Set|fialc[4762]|0x10...
Hey, for some reason after erasing the running-config on the XR-VM via "commit replace" the System only boots to the sysadmin Login prompt on the Serial console. I can Login but I don't know how to switch to the XR-console.Typing "Exit" gets me to th...
Hello,during SMU installation on NCS5501-SE, IOS XR 7.1.2 I almost run out of a disk space. Here is the warning%HA-HA_WD-3-DISK_ALARM_ALERT : A monitored device / ( rootfs:/ ) is above 80% utilization. Current utilization = 85. Please remove unwanted...
Hi, Guys, There are multiple IS-IS instances which are both running with Level-2 only in the network, and I do not want to leak the routes between these IS-IS instances, how to implement this stuff? Appreciate!
Hi Expert,Anyone have seen log IP-TCP_NSR-5-DISABLED? NSR disabled for TCP connection because Retransmission threshold exceeded.BGP connection cannot be established for while before rollback to be normal. No link flap. Should it be bug software? Tha...
Our lab no longer has redundant pairs of RSP880's as a RSP880-SE had to be moved to another location for a new lab. We're trying to do some interoperability using A9K-8X100GE-TR. A single RSP880 will be rate limited so we need 2. Are there any iss...
Hi
Is there a way to show current configuration in a context in configuration mode?
as an example
RP/0/RSP0/CPU0:9k(config)#l2vpn bridge group L2_DCS bridge-domain 502RP/0/RSP0/CPU0:9k(config-l2vpn-bg-bd)#
If i stand here the only way to see active c...
Hello The led on 0/RSP0/CPU0 is on with a message RP/0/RSP0/CPU0:BSRZGZ01#show environment leds detailsFri Feb 19 14:57:45.427 METR/S/I Modules LED Status Alarm Reason0/RSP0/*host Critical-Alarm On Card temp. beyond range;host Major-Alarm Off ----ho...
Hi Everyone,We are tying to apply multiple polices for one subscriber using Both dynamic policy download and manual method. In both method I can see only last service activation requested policy and access-list have applied to the particular subscrib...
Online I can find very limited info on A99-RP2-SE. What I found is that they support ASR9912 & ASR9922. Will the RP2-SE work on other ASR9900 CHASSIS, ie ASR-9904, 9906? Thanks!