Hi everyone, Is there any way to control the packet loss measurement for SLM/Y1731 on ASR9k? For example, I have created a probe to send 60 packets every second, but it happens I lose one packet, therefore the packet loss would be 1/60=1.67%, which ...
Forum Posts
Hi I need help in an IOS-XR setup. I have 2 Routers ASR 9K, where each is connected to a Firewall. FW pair work in Active Standby Setup. The Router which is connected to Active FW receives the ARP for the virtual IP of the FW pair and the other one d...
Hi all is there any equivalent IOS XE "no bgp default route-target filter" command on IOS XR? Regards Seek
Resolved! OSPF load-sharing is not working
Dear Experts, I have a question about load-sharing in OSPF 。 There are two equal-cost routes in the routing tale, in my idea, the forwarding behavior should be load-sharing. however, the traffic is forwarding on one uplink. Below is "show" info: ...
Hi Guys, I want to install Service Pack (SP3) for an ASR9k IOS-XR 6.5.3 and I'm trying to find the release notes but, I couldn't find any.So, the question is, do you know of any release notes for service packs or recommendations or just go ahead and ...
I know in IOS XRv L2VPN only supports control plane but not the data plane. I just want to get clarification, why l2vpn not supported on IOS XRv and why the relase note of IOS XRv 6.2.25 does not gave any information about L2VPN (https://www.cisco.co...
Hi,Cisco recently released Cisco XRv 5.1.1 which is IOS XR running in a VM. I thought it would be nice track features working not working and if Cisco could comment on the roadmap.Working:ISISBGPLDPNot working:EoMPLSVPLSControl plane is up for EoMPLS...
Hi All, We have done PBR configuration on our ASR 903 Router , each and every configuration the device has taken , then also the policy based routing is not taking place , kindly give your inputs for resolving the issue , below is the configuration :...
Hello!I test functions BNG for future migration from ASR1002 to ASR9001. PPPoE session worked up. IPoE session with L2-connected subscribers worked up. But when i configure on subinterface L3 routed session interface Bundle-Ether8.100description == t...
Hello, I am standing up 2 ASR 9906 routers. The organization I work for uses Paessler's PRTG to monitor our devices. I have had no issues monitoring interfaces stats, cpu, memory, etc. However, I am trying to monitor the peer state for BGP, by using ...
Resolved! ASR 9000 - Monitor NP Interface command
If I have IOS XR Code 6.1.4, can I run the 'monitor np interface' command and not cause any NP blips? For example, if I want to run it on a sub-interface going towards a customer? I know if you do 'monitor np capture' that will cause a 50ms blip, but...
Hi Community, Question about possibility to copy a file between two ASR devices - is it supported? If so then lets say i have a file asr-new-software.tar on harddisk: and now how the scp line should look like?When I try the below one it does not seem...
I believe that the VSM's are EOL and would like to know if it will be possible to do CGNAT on the current ASR9906 or ASR9910 platforms. If yes what is required. If no I assume I will need a firewall to NAT. Any recommendation on a firewall for 2500 w...
I've learned through my previous post that Segment Routing TILFA node and SRLG protection will be supported in IOS XR 6.1.1. (Thanks kmichiel!) I wonder if the release would include the On-Demand Nexthop (ODN) functionality as well? If it does I woul...
Hello all,anyone tried to create migration configuration for IOS-XR 32-bit->64-bit migration? I have updated the CSM Server to Version 4.2 and at least for me it seems to be broken. I getting follwing error out of System log traces: Traceback (most r...