hi I am getting this fan speed , is that abnormal : Fan speed (rpm) and run time (in hours) : FAN0 FAN1 FAN2 FAN3 FAN4 FAN5 0/FT0/* (Speed) 12960 12600 12300 12330 12570 118500/FT0/* (Run Time) N/A ...
I am trying to make this work, I have a 9k in the middle that should bridge this together but I cant ping through. 10.1.1.1 --> Junos switch vlan 10 --> Asr9k {l2transport dot1q10 (bridge 10 with routed bvi) --> l2transport dot1q2000 (bridge 2000 wi...
I have full route table but I can not figure out where to add routes for advertisement? Nothing works. Can anyone help me out? route-policy PASS-ALLpassend-policyroute-policy IPV6-PASS-ALLpassend-policy#sh run router bgprouter bgp ###82nsrbgp router-...
Hello Could you let know if it is normal FAN Speed 0/FT0/* on a Cisco ASR9010 running 5.3.4.I have two device in cluster, this device are in differente side, but I need to know of 0/FT0/* (Speed) in 9390 is normal until that change fan (because FAN 2...
I have been beating head against wall, I cant figure out problem. I have ### numbers for obvious reasons. What I do know is I have 100% connectivity over p2p's. From what I can tell I am set up correct, please can someone help. BGP router identifier...
Anyone know how to set IFE port-group to 1G on a A9K-24X10GE-1G-TR ? Seeing this module's ports are configured in IFE port-groups(https://www.ciscolive.com/c/dam/r/ciscolive/emea/docs/2018/pdf/BRKARC-2003.pdf) After significant searching I can't fin...
Hello expertsWe currently have an ASR 9904 that has a RSP440-TR and a 24*10GE-TR Line card.We bought another RSP440-TR to put in the chassis . Can we put the RSP in when the router is running ? and Do we have to do any configuration for new RSP or t...
HelloI got the following when trying to configure SSH on an ASR9K:RP/0/RSP0/CPU0:hk4-vipasr1(config)#ssh ? ^% Invalid input detected at '^' marker.RP/0/RSP0/CPU0:hk4-vipasr1(config)#do sh install active Node 0/RSP...
Hello,I am getting an error while booting the linecard : PLATFORM-NP-0-INIT_ERR : Device BST memory test failure 0x80001761 on NP channel 7 external TM memoryThere are a lot of other errors but I think it's the one related to my issue.It does a kerne...
Hi AllI am trying to upgrade my IOS-XR from 5.3.2 to 6.2.2, but fail with following errors, anyone can assist me on this , i have all all the PIE in the install , and install activate causing this : \ 1% complete: The operation can still be aborted ...
Is there any benefit in configuring both NSR and NSF on the routing protocols that support it? I understand that NSR can work independently to keep routing adjacencies up without the neighbors assistance, while NSF both routers need to have it enable...
Hi all,I've recently started working with mLACP and I'd like to know if it's compatible with L3VPNs.All cisco documentation that I've read neither shown any restriction nor examples about the integration of L3VPNs, only L2VPNs like VPLS. I'm working ...
Dear Support,We upgrading IOSxr 64 bit 6.3.2 to 6.5.3.We can not upgrade as the rootfs: has not enough free space.As a workaround we removed some unecessary packages. (on an other router we had to remove necessary package as well)After the upgrade we...
I'm currently operating an ASR9010 on IOS XR v5.3.4 with a A9K-8T-L in LC slot 1 and 2x RSP440-SE in a redundant configuration. A few weeks ago, I noticed the following errors in my log:pfm_node_rp[357]: %PLATFORM-CROSSBAR-1-SERDES_ERROR_LNK0 : Set|f...
