Hi, We have a couple of Cisco ASR 9006's which we are looking at upgrading to 6.2.3, Can we directly upgrade from 5.3.3 (32bit) to 6.2.3 (32bit)? Looking at the upgrade documentation it suggests their might be a need to install bridge SMUs before...
Forum Posts
We are running a textbook MPLS VPN using EIGRP as the IGP on ASR 9006s running a mix of IOS XR 6.2.3 and 5.3.4. Before Non-Stop Routing (NSR) was enabled for LDP we experienced a 60+ second outage on VPN traffic when performing a 'redundancy switch...
# sho bfd ipv6 session detail SpoilerI/f: Bundle-Ether1.751, Location: 0/0/CPU0Dest: 2001:b1:fe0:5::1Src: 2001:b1:fe0:5:: State: DOWN for 0d:0h:21m:25s, number of times UP: 0 Session type: SW/V6/SH/BLReceived parameters: Version: 0, desired tx inte...
I don't seem to be able to get SNMP information on a second ISIS process running on an XR device with the following specs: Hardware: ASR 9904 Software: Version 5.3.3 Here are the neighbors I know the router has and the SNMP MIB support: RP/0/RSP1/CP...
if we have 100 users 50 are using video ip phones what are more requirements we in the network?
Hello We are trying to build some tools that keep track of the state of the ASR9000 in our network (e.g. linecards installed, interface description). Normally we would periodically login in the routers, run a set of commands and retrieve the necess...
Resolved! BGP VPNV4 Routes in XR
Hi, Is there any way to filter out routes based on route-target in XR platform? If i want to find out routes specific to RT 1:1 in a vrf or in complete bgp vpnv4 table, how can I do that through show commands? If there is no specific command for RT...
Does anyone help me to understand concept of Super VLAN? Thank you, Sohan
I apologize as I am still trying to learn routing policies for Cisco. Does ISIS need a routing policy to accept routes from neighbors? Maybe I am thinking it is similar to JunOS. I am able to form an adj. between my iOS-XRv VM and my physical router....
Hi there, Based on the following configuration, I have some PPPoE subscribers connected to a BNG which is ASR 9912,each user assigned to a service profile defined in AAA and ASR which contains two sub-service(or may be more in the future); one of t...
I am new to ios-xr i tried configuring prefix list usingprefix-set <name> i need to give all the prefixes in a single line seperated by comma as show belowRP/0/RSP0/CPU0:ios(config)#prefix-set abcRP/0/RSP0/CPU0:ios(config-pfx)#RP/0/RSP0/CPU0:ios(conf...
Hi all - I'm looking to install CSM 3.5.1. I'm assuming it needs to communicate with CCO, but I don't see any sort of firewall port list mentioned in the install guide to enable that. If needed, does anyone know or have a pointer where that info can...
Good morning, Carissimos, I need your support, recently I noticed that when I try to execute the "ping" or "traceroute" commands to a peer-to-peer IP address with or without source, I get this message "% Invalid destination ipaddress" as below: R...
Hello, Is there any way to filter routes from ISIS database to routing table on ASR9k ? It is possible on IOS XE, Huawei, Nokia and other platforms. Thanks all
Resolved! Figuring the QOS out...
Ok so i have ipv4 IPOE subs working more or less they get the IP from dhcp get access, but not that i'm trying to implement QOS i'm hitting an issue i am using a ASR9001 for our BNG. i attempted to use a COA to set a speed coa_w32.exe -n 172.16.0.1...
