cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2933
Views
10
Helpful
3
Replies

CRS traffic shaping and policing

Hello,

i just moved services from GSR 12404 to CRS1/8 and there is no possibility do add service-policy to L3 subinterface.

RP/0/RP0/CPU0:XXX#conf t

Fri Dec  9 09:25:55.690 CET

RP/0/RP0/CPU0:XXX(config)#interface tenGigE 0/0/0/0.900

RP/0/RP0/CPU0:XXX(config-subif)#service-policy input 300mbps

RP/0/RP0/CPU0:XXX(config-subif)#commit

Fri Dec  9 09:26:06.587 CET

% Failed to commit one or more configuration items during a pseudo-atomic operation. All changes made have been reverted. Please issue 'show configuration failed' from this session to view the errors

RP/0/RP0/CPU0:XXX(config-subif)#show configuration failed

Fri Dec  9 09:26:11.842 CET

!! SEMANTIC ERRORS: This configuration was rejected by

!! the system due to semantic errors. The individual

!! errors with each failed configuration command can be

!! found below.

interface TenGigE0/0/0/0.900

service-policy input 300mbps

!!% 'qos_ea' detected the 'fatal' condition 'QoS is not supported on sub-interfaces'

!

end

Any help ?

1 ACCEPTED SOLUTION

Accepted Solutions
Alexei Kiritchenko
Cisco Employee

Hello Dragoljub,

Qos on vlan interfaces is not supported for FP140/FP40 LCs.

“MQC-based QoS configuration will be accepted only on the port level but not on the VLAN subinterface level.”

http://www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r3.8.4/general/release/notes/reln_384.html

Regards,

/A

View solution in original post

3 REPLIES 3
Alexei Kiritchenko
Cisco Employee

Hello Dragoljub,

Qos on vlan interfaces is not supported for FP140/FP40 LCs.

“MQC-based QoS configuration will be accepted only on the port level but not on the VLAN subinterface level.”

http://www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r3.8.4/general/release/notes/reln_384.html

Regards,

/A

Actualy it is possible to match VLAN on physical interface and make something like this.

interface TenGigE0/0/0/0

service-policy input customers-qos

service-policy output customers-qos

interface TenGigE0/0/0/0.100

desc customerA

interface TenGigE0/0/0/0.101

desc customerB

class-map match-any vlan100

match vlan 100

end-class-map

!

class-map match-any vlan101

match vlan 101

end-class-map

policy-map customers-qos

class vlan100

  police rate XXX mbps

   conform-action transmit

   exceed-action drop

  !

!

class vlan101

  police rate XXX mbps

   conform-action transmit

   exceed-action drop

  !

!

This works perfect.

Hello, 

I am trying to configure QoS in CRS with FP140. We have the release 4.2.1.

This link has an example but we are receiving the same error.

http://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-2/lxvpn/configuration/guide/vc42book/vc42v2.html#wp1077050

 

Do you know if this support is hardware based?

Thank you