cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2140
Views
0
Helpful
6
Replies

EVPN Convergence time in a Multihome setup is about 20 seconds. 2 slow

EVPN Convergence time in a Multi home setup is about 20 seconds. It's too slow.

I have one CE  connected to two PE1 and PE1.

PE1 and PE1 are connected to the MPLS core. From MPLS core there is another PE3. I'm running an 10G RFCtest between the Customer 1 device and Customer 2 device. 

I'm testing resiliency, and see how fast it can converge. Currently, both PEs are load balancing the traffic. When I reload PE1,   PE2 start to pass all the traffic. The problem is that when PE2 is about to reestablish the BGP neighborship with the RRs  PE1 stops passing traffic. Once PE2 finally reestablish BGP peers with the router reflectors, traffic starts to pass normally.   I'm read a tons of documents about how to improve the convergence time. the only one that made sense to me is the "bgp graceful-restart"

This is an ALL active MH secenario. With an ethernet segment.  I'm about to lab this with with the startup cost-in command to see if will help.    my question is are there any good articles that talk about SPECIFICALLY ALL ACTIVE MULTIHOME WITH BUNDLE scenerio that talks about improving the convergence time.  or a configuration that you will recommend.  I read 

 

 

 

1 Accepted Solution

Accepted Solutions

I found the solution. Once I applied the  core-isolation-group  the convergence time dropped to ms

View solution in original post

6 Replies 6

tkarnani
Cisco Employee
Cisco Employee
We can check this command during the time of the reload, we want to check which timer is running
show evpn ethernet-segment interface bundle-Ether <> carving


Peering timer : 3 sec [not running]

Recovery timer : 30 sec [not running]


Thanks

I found the solution. Once I applied the  core-isolation-group  the convergence time dropped to ms

jigojar
Level 1
Level 1

we are facing the convergence issue during the acces ring failure. its taking 300 seconds to switch the traffic.

 

 

interface GigabitEthernet0/0/0/21
ethernet-segment
identifier type 0 10.70.25.27.11.22.33.44.66
load-balancing-mode single-flow-active
convergence
mac-mobility
!
!
timers

 

300 se c is default MAC flush timer so it looks some TCN which should be generated upon your convergence trigger are not traveling through.

Can you pls provide more details of:

- Your topology

- HW/SW used

- Full config from each PE involved

- Describe the trigger you do for convergence

- Describe which flows (Source and Destination) are affected

 

Thx

Niko

HTH,
Niko

jigojar
Level 1
Level 1

Hi,

pls find the config

 

evpn
!
interface GigabitEthernet0/0/0/10
ethernet-segment
identifier type 0 10.07.02.52.22.52.24.13.10
load-balancing-mode single-flow-active
convergence
mac-mobility
!
!
!
timers
peering 0
!


bridge group ENT_BCF-BCF_SVPN_2444_STAG
bridge-domain ENT_BCF-BCF_SVPN_2444_STAG
storm-control broadcast kbps 256
mac
withdraw state-down
!
interface GigabitEthernet0/0/0/10.2444
storm-control unknown-unicast kbps 256
storm-control broadcast kbps 256
split-horizon group
!
evi 2444
!

evpn
evi 2444
bgp
route-target import 100.70.252.1:2444
route-target export 100.70.252.1:2444
!
etree
rt-leaf
!
advertise-mac
!
!EVPN.jpg

 

jigojar
Level 1
Level 1

Hi Can some one help us to reduce the convergence time