ā08-04-2020 09:29 PM
HI
Whenever I try to configure IPSLA in XRv9 I encountered an error about this feature has no resources and cannot be enabled.
Is there any workaround for this? Is it supported in XRv9?
Thank you
Solved! Go to Solution.
ā08-06-2020 02:35 AM
I believe only UDP echo is supported not ICMP echo as per the trace below.
RP/0/RP0/CPU0:xrv# show ipsla trace sub-agent initialization Thu Aug 6 09:25:57.555 UTC 17 wrapping entries (9728 possible, 384 allocated, 0 filtered, 17 total) Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA init: Using PD Capabilities: Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: ICMP_ECHO=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: ICMP_PATHJITTER=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: ICMP_PATHECHO=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: UDP_JITTER=ENABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: UDP_ECHO=ENABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: MPLS_LSP_PING=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: MPLS_LSP_TRACE=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: MPLS_LSP_GROUP=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: UDP_JITTER_CHECK_CFG=ENABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: UDP_JITTER_MIN_INTERVAL=10 Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: TWAMP_SERVER=ENABLED Aug 6 09:25:27.786 ipsla/sa/init 0/RP0/CPU0 t18520 Operation Table module init: complete Aug 6 09:25:27.786 ipsla/sa/init 0/RP0/CPU0 t18520 Thread Pool module init: complete Aug 6 09:25:27.796 ipsla/sa/init 0/RP0/CPU0 t18520 Rate Limit module init: Maximum pps rate:15, Minimum interval:70 msec Aug 6 09:25:27.796 ipsla/sa/init 0/RP0/CPU0 t18520 LSPV Connection module init: complete Aug 6 09:25:27.796 ipsla/sa/init 0/RP0/CPU0 t18520 Event module init: complete
ā08-06-2020 09:10 AM
That is correct, in xrv9k only UDP probes are supported, not ICMP.
Sam
ā08-05-2020 12:56 PM
Can you share the confirmation you were trying to apply and version of xrv9k?
Thanks,
Sam
ā08-06-2020 12:19 AM
Hi
This is the requested Information:
Thu Aug 6 07:24:02.223 UTC
Cisco IOS XR Software, Version 6.6.2
Copyright (c) 2013-2019 by Cisco Systems, Inc.
Build Information:
Built By : ahoang
Built On : Fri Apr 26 15:47:48 PDT 2019
Built Host : iox-ucs-033
Workspace : /auto/srcarchive16/prod/6.6.2/xrv9k/ws
Version : 6.6.2
Location : /opt/cisco/XR/packages/
cisco IOS-XRv 9000 () processor
System uptime is 2 minutes
RP/0/RP0/CPU0:XRv9(config)#ipsla
RP/0/RP0/CPU0:XRv9(config-ipsla)#operation 1
RP/0/RP0/CPU0:XRv9(config-ipsla-op)#type icmp echo
RP/0/RP0/CPU0:XRv9(config-ipsla-icmp-echo)#destination address 10.10.10.10
RP/0/RP0/CPU0:XRv9(config-ipsla-icmp-echo)#frequency 5
RP/0/RP0/CPU0:XRv9(config-ipsla-icmp-echo)#commit
Thu Aug 6 07:25:13.444 UTC
% Failed to commit one or more configuration items during a pseudo-atomic operation. All changes made have been reverted. Please issue 'show configuration failed [inheritance]' from this session to view the errors
RP/0/RP0/CPU0:XRv9(config-ipsla-icmp-echo)#show configuration failed
Thu Aug 6 07:25:20.212 UTC
!! SEMANTIC ERRORS: This configuration was rejected by
!! the system due to semantic errors. The individual
!! errors with each failed configuration command can be
!! found below.
ipsla
operation 1
type icmp echo
destination address 10.10.10.10
!!% 'ipsla' detected the 'resource not available' condition 'Not supported'
frequency 5
!!% 'ipsla' detected the 'resource not available' condition 'Not supported'
!
ā08-06-2020 02:35 AM
I believe only UDP echo is supported not ICMP echo as per the trace below.
RP/0/RP0/CPU0:xrv# show ipsla trace sub-agent initialization Thu Aug 6 09:25:57.555 UTC 17 wrapping entries (9728 possible, 384 allocated, 0 filtered, 17 total) Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA init: Using PD Capabilities: Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: ICMP_ECHO=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: ICMP_PATHJITTER=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: ICMP_PATHECHO=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: UDP_JITTER=ENABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: UDP_ECHO=ENABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: MPLS_LSP_PING=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: MPLS_LSP_TRACE=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: MPLS_LSP_GROUP=DISABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: UDP_JITTER_CHECK_CFG=ENABLED Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: UDP_JITTER_MIN_INTERVAL=10 Aug 6 09:25:27.784 ipsla/sa/init 0/RP0/CPU0 t18520 Event module IPSLA SA caps: TWAMP_SERVER=ENABLED Aug 6 09:25:27.786 ipsla/sa/init 0/RP0/CPU0 t18520 Operation Table module init: complete Aug 6 09:25:27.786 ipsla/sa/init 0/RP0/CPU0 t18520 Thread Pool module init: complete Aug 6 09:25:27.796 ipsla/sa/init 0/RP0/CPU0 t18520 Rate Limit module init: Maximum pps rate:15, Minimum interval:70 msec Aug 6 09:25:27.796 ipsla/sa/init 0/RP0/CPU0 t18520 LSPV Connection module init: complete Aug 6 09:25:27.796 ipsla/sa/init 0/RP0/CPU0 t18520 Event module init: complete
ā08-06-2020 03:22 AM
hi
Thank you for the guidance
ā08-06-2020 09:10 AM
That is correct, in xrv9k only UDP probes are supported, not ICMP.
Sam
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: