I'm looking to get some basic reporting from FMC for things like top talkers but can't seem to do it in FMC because a lot of the logs are not going to the event viewer due to its limited size. What is a simple tool that can be integrated to get repo...
Forum Posts
Planning to upgrade/replace ASA5525X with Firepower1120 Series loaded with ASA image. Need proper guidance on1. How to perform this move.2. Things to keep in mind.3. Can I simply load existing config on FPR1120 and turn it on. Will everything work ju...
Good day everyone.Yesterday, I was working on a Cisco ASA 5512-X Firewall that was being used as a VPN Firewall when suddenly I was disconnected from the ASDM. My SSH session from Putty was closed, and I am unable to get back into any of them. I took...
Resolved! device-tracking mode guard vs legacy DAI
reading Feature history of SISF Security Configuration Guide, Cisco IOS XE Dublin 17.12.x (Catalyst 9400 Switches) - Configuring Switch Integrated Security Features [Support] - Cisco i have a feeling that device-tracking mode guard is an alternative ...
Hi, I have one pair of FMC and on pair of FTD, currently FMC appliances in HA setup and we have successfully integrated with ISE pxGrid. The question now is what will happen if the primary FMC fails, will FTD HA still receive the IP-to-SGT mapping fr...
Hello everyone, I'm trying to use the Firewall Migration Tool (FMT v7.0.1) to migrate the config of ASA 9.12 to FMC 7.4.2. After successfully uploaded the the text file of ASA running config into FMT, and then started the conversion after selected th...
Hi all, Is anyone here also experience this kind of issue on the FTD? we notice that some return traffic being blocked on the FTD. Thanks for the answer!!
Hi Team, We have old Cisco ASA need to confirm that config and sessions are synced to the Passive ASA????? This host: Secondary - ActiveActive time: 30555250 (sec)slot 0: ASA5515 hw/sw rev (1.0/8.6(1)2) status (Up Sys)Interface INSIDE (10.30.136.10):...
Currently on a Cisco ASA, we use RADIUS authentication for WEBVPN users. For the logs on the RADIUS server we are not receiving the originating public IP of the users failed/successful attempts, rather we are getting OUR public IP of the gateway for ...
Hello, We have a customer who is running their perimeter firewalls in Active Passive failover. The firewalls in single context mode. I have the below queries regarding the Mac address that will be used by the primary unit. 1. What will be the MAC a...
On my FMC, I recently noticed an issue when I try to access the module exclusion web page under System > Health > Exclude. When I click on the menu, I get the following error:Error while fetching dataDetails{"errors":[{"instancePath":"/2/excludedMod...
Hi Folks, I'm having some issues I have an outside network 10.246.133.192/26 and inside host in network 10.244.17.99. The traffic between them is hitting for the temporary full access rule and doesnt hit the specific rule i've already applied. I'm at...
Hello I configured Threat detection on my FTD firewall over the weekend. Can someone please explain what the disabled section of this command means? https://www.cisco.com/c/en/us/support/docs/security/secure-firewall-threat-defense/222383-configure...
we are going to migrate the asa to ftd fmc so in the migration documents mention trustpoint certificate as per-requisites.so my querry is where can i find this certificates and how to export/migrate this from asa to ftd fmc.
Hello, we have a new install of FTDv to try it out before buying an appliance, we tried deploying to Hyper-V and also to VMware. VMware install was completely dead with no communication to the outside world (I presume it wants 10gig interfaces we don...
