公司有几个SAP1602I-C-K9，之前是胖的，后来买了AC，全改成瘦的了，用的固件都是一样的，有几个能正常注册到AC上，有一个加入不了，求教是什么原因，以下是加入不了的AP信息：
IOS Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 16 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6010368
flashfs[0]: Bytes available: 25925632
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: f0:7f:06:54:46:1c
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...##############
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x2004000
executing...
Secondary Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 16 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6010368
flashfs[0]: Bytes available: 25925632
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: f0:7f:06:54:46:1c
Secondary bootloader Ethernet not enabled, skip ether_init
Boot CMD: 'boot flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx;flash:/ap1g2-rcvk9w8-m
x/ap1g2-rcvk9w8-xx'
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx"...#######################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx" uncompressed and installed, entr
y point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.3(3)JBB6, RELEA
SE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Sun 01-Nov-15 20:18 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Micronix MX25L256_35F
flashfs[2]: 16 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 6010368
flashfs[2]: Bytes available: 25797632
flashfs[2]: flashfs fsck took 10 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-SAP1602I-C-K9 (PowerPC) processor (revision B0) with 187382K/74672K by
tes of memory.
Processor board ID FGL1726S8SP
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.1.131.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F0:7F:06:54:46:1C
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18356J5N
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1726S8SP
Top Revision Number : A0
Product/Model Number : AIR-SAP1602I-C-K9
% Please define a domain-name first.
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.671: APAVC: Initial WLAN Buffers Given to System is 500
*Mar 1 00:00:12.687: APAVC: WlanPAKs 9355 RadioPaks 8747
*Mar 1 00:00:13.331: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:14.759: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:15.679: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.3(3)JBB6, RELEA
SE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Sun 01-Nov-15 20:18 by prod_rel_team
*Mar 1 00:00:15.711: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:15.711: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 00:00:15.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:16.759: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
*Mar 1 00:00:18.251: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init:
MIC Present and Parsed Successfully
*Mar 1 00:00:27.691: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:28.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to down%Default route without gateway, if not a point-to-point interfa
ce, may impact performance
*Mar 1 00:00:34.379: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:34.451: Cert ISSUER (42): cn=Cisco Manufacturing CA,o=Cisco System
s
*Mar 1 00:00:34.455: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:36.467: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:37.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
*Mar 1 00:00:40.051: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 192.168.4.10, mask 255.255.255.0, hostname APf07f.0654.461c
%Error opening flash:/capwap-saved-config (No such file or directory)
*Mar 1 00:00:44.511: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_DETECTE
D_PD inline power source
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (211.136.192.6) [OK]
*Mar 1 00:01:05.555: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:01:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:01:01.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:01:01.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:01:06.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:01:59.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:01:59.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:01:59.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:02:00.019: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:02:10.091: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:02:10.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:02:10.439: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:02:10.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:02:15.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:03:09.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:03:09.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:03:09.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:03:10.015: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:03:20.083: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:03:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:03:20.439: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:03:20.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:03:25.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:04:19.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:04:19.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:04:19.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:04:20.015: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:04:30.083: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:04:30.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:04:30.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:04:30.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:04:35.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:05:29.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:05:29.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:05:29.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:05:30.015: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:05:40.083: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:05:40.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:05:40.439: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:05:40.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:05:45.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:06:39.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:06:39.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:06:39.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:06:40.015: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:06:50.083: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:06:50.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:06:50.443: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:06:50.443: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
AC里看到的信息：
IOS Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 16 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6010368
flashfs[0]: Bytes available: 25925632
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: f0:7f:06:54:46:1c
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...##############
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x2004000
executing...
Secondary Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 16 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6010368
flashfs[0]: Bytes available: 25925632
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: f0:7f:06:54:46:1c
Secondary bootloader Ethernet not enabled, skip ether_init
Boot CMD: 'boot flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx;flash:/ap1g2-rcvk9w8-m
x/ap1g2-rcvk9w8-xx'
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx"...#######################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx" uncompressed and installed, entr
y point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.3(3)JBB6, RELEA
SE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Sun 01-Nov-15 20:18 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Micronix MX25L256_35F
flashfs[2]: 16 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 6010368
flashfs[2]: Bytes available: 25797632
flashfs[2]: flashfs fsck took 10 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-SAP1602I-C-K9 (PowerPC) processor (revision B0) with 187382K/74672K by
tes of memory.
Processor board ID FGL1726S8SP
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.1.131.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F0:7F:06:54:46:1C
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18356J5N
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1726S8SP
Top Revision Number : A0
Product/Model Number : AIR-SAP1602I-C-K9
% Please define a domain-name first.
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.671: APAVC: Initial WLAN Buffers Given to System is 500
*Mar 1 00:00:12.687: APAVC: WlanPAKs 9355 RadioPaks 8747
*Mar 1 00:00:13.331: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:14.759: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:15.679: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.3(3)JBB6, RELEA
SE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Sun 01-Nov-15 20:18 by prod_rel_team
*Mar 1 00:00:15.711: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:15.711: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 00:00:15.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:16.759: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
*Mar 1 00:00:18.251: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init:
MIC Present and Parsed Successfully
*Mar 1 00:00:27.691: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:28.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to down%Default route without gateway, if not a point-to-point interfa
ce, may impact performance
*Mar 1 00:00:34.379: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:34.451: Cert ISSUER (42): cn=Cisco Manufacturing CA,o=Cisco System
s
*Mar 1 00:00:34.455: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:36.467: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:37.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
*Mar 1 00:00:40.051: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 192.168.4.10, mask 255.255.255.0, hostname APf07f.0654.461c
%Error opening flash:/capwap-saved-config (No such file or directory)
*Mar 1 00:00:44.511: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_DETECTE
D_PD inline power source
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (211.136.192.6) [OK]
*Mar 1 00:01:05.555: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:01:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:01:01.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:01:01.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:01:06.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:01:59.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:01:59.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:01:59.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:02:00.019: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:02:10.091: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:02:10.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:02:10.439: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:02:10.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:02:15.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:03:09.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:03:09.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:03:09.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:03:10.015: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:03:20.083: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:03:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:03:20.439: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:03:20.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:03:25.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:04:19.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:04:19.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:04:19.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:04:20.015: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:04:30.083: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:04:30.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:04:30.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:04:30.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:04:35.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:05:29.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:05:29.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:05:29.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:05:30.015: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:05:40.083: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:05:40.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:05:40.439: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:05:40.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
*Jan 11 03:05:45.439: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
*Jan 11 03:06:39.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.4.248:5246
*Jan 11 03:06:39.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:06:39.999: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Jan 11 03:06:40.015: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 11 03:06:50.083: AP has SHA2 MIC certificate - Using SHA1 MIC certificate f
or DTLS.
*Jan 11 03:06:50.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.4.248 peer_port: 5246
*Jan 11 03:06:50.443: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.4.248 peer_port: 5246
*Jan 11 03:06:50.443: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.4.248
AC里看到的信息：
