This is in relation to a LAB I'm building to test produciton systems in a sandbox by cloning the VM and migrating from production ESXi host to the lab ESXi host within the same vCenter. The other host has its own VMM domain (vDS) and a pair of disjoi...
Forum Posts
Hello On the ACI factory in one of the sites after upgrading to version from 4.2(7w) 5.3(2d) we record a slow response from the APIC servers when executing configuration and show commands via CLI. The problem is especially noticeable when executing v...
Hello, I have the below scenario: Tenant named SHG contains EPG1 and EPG2 Tenant common has vrf: default defined BD1-EPG1 and vrf: VRF2 -BD2-EPG2. Under common tenant I have a contract named route_leak_contract with global scope provided by EPG1 a...
hello all , i have one problem if anyone can support . 1-have two Leafs connect to remote server with one port channel 2-this port channel have MGM VLAN and traffic VLAN 3-MGM VLAN should be bind to EPG with BD and route to specific VRF 4-traffic VL...
Hi all,in the next months we will do a migration from a legacy Nexus environment to a greenfield Cisco ACI. I am studying the better ways to do this.We decided to proceed with network-centric approach (1BD-1EPG-1VLAN); we will connect ACI to legacy i...
Resolved! Nutanix and Cisco UC
Is it Cisco UC officially support the Nutanix server? Any Benefits to use Nutanix server on Cisco UC?
hello, does ACi support 802.1x on access ports of leaf switches for external devices? i need t oconnect some weird devices.the config guide says: "On the menu bar, click Fabric > External Access Policies > Policies > Interface > 802.1X Port Authentic...
Hey Folks, I'm upgrading my ACI fabric within two stages from: 5.2(3) to 5.2(8i)From 5.2(8i) to 6.0(7e)(M) Based on Cisco recommendation, any Cisco App Center should be disabled prior to the upgrade process. I found my customer has the "Nexus Insight...
Resolved! APIC VPC clean-up
I'm running APIC v4.2(7f) and my ACI data center consists of Nexus 9300 Leaf switches. I have over a thousand VPC configurations that need to be cleaned up (removed) and I wanted to ask if there was a site where I can look at scripts in helping do th...
Hello everyone.We are using vAPIC 6.0.5 with some C93180fx & C9332c as spines.Everything works fine, but when I create contact (in Application Profile-Topology), I cant submit & apply contact to my EPGs !As a tip, when I create a contract, the contra...
Hi all,I am going to uprade an ACI fabric from release 4.2(4i) to 5.3(2d).I checked the release notes for APIC 5.3 (link) and I verified that my current CIMC version (4.0(1a)), although it is not the recommended, is in the list of the compatible ones...
I am plaining for spine switch replacement in ACI fabric and want to know what are the prechecks are required before replacing the spine switch ? also, How to be retained polices on the existing ports SPINE ? and how to validate the traffic on the S...
Hi everyone, I'm configuring LDAP authentication on NDO and had a couple of questions: Is there a way to authenticate directly using existing LDAP usernames and passwords without needing to create a specific user for NDO? Based on the documentation ...
Hello, on a customer tenant we configured an L3Out (SVI mode) with 2 ports connected to 2 Cato Socket devices in HA During the failover test we had the following issue: If we shut the leaf port where the cato1 is connected the cato2 become master an...
How can we replace the spine hardware to N9K-C9332D-GX2B in cluster Version 4.2(7u)(Spine current version 14.2(7u)) since N9K-C9332D-GX2B ONLY supported from release 15.2.3 to release 16.1.1. Also we can not upgrade cluster to 5.X due current spine H...
