I am working on adding three new ESXi hosts to an ACI fabric and would like these new hosts to have access to the same DVS that the current servers have access to. The current ESXi servers are connecting to a fabric interconnect which connects to th...
Hi,I am new to ACI and was recently looking at the operations tab and ran a query and I am not sure that I understand the results. I have a host that sits outside of ACI (10.131.161.38) and a host inside of ACI (192.168.209.148) I can happily ping fr...
Hi ACI board,I integrated a standby APIC into my fabric.When using the command "show controller" on a APIC within my fabric, the standby APIC is listed in the output with the status "data-layer-partially-diverged".Is this the normal behavior? Can any...
I have EIGRP established and exchanging routes between ACI and Nexus 7K's. Everything is working but the routes learned from ACI are showing: Minimum bandwidth is 100000 Kbit The links between the two are 10GB, I I have tried to change EIGRP Interfa...
Hi everyoneI've connected HPE Blade servers via VPC to Cisco ACI fabric leaves. In blade servers we have ESXi hosts and no vmm integration. The L3Out and intra epg communication is OKBut the inter EPG does not work when source and destination endpoin...
Hi Team, Follow this document:https://www.cisco.com/c/en/us/solutions/collateral/data-center-virtualization/application-centric-infrastructure/white-paper-c11-739971.htmlThe docs introduce about PBR destination in L3Out using 2 Arm mode starting vers...
i got this device from my friend and it not booting so im trying to boot it from tftp and install nxos on it but i got this error and this is my device log : CISCO SWITCH Ver7.17Device detected on 0:6:0 after 0 msecsDevice detected on 0:1:1 after 0 m...
Hi I would like to upgrade ND+NDO to latest recommended version. Based on BRKDCN-2980.pdf I think NDO version I should go to is 4.1(2b) Current versions:* ND 2.2(2d)* NDO 3.7.2d Question: My current policy objects contain circular references. Before ...
Hi, I have a new pod config we are trying to get working. We have a 400g spine and would like to breakout a port from 400g to 4x100g. I see how to do this in the apic for a leaf, but not for a spine. My spine is a 9332D-GX2B, my codes are at 5.2.(...
Trying to fresh install the fabric from .iso and when booting the server it gets stuck to the copyright page. See attach screenshot. Using image 5.2.7g the recommended code. APIC-M2-SERVER
Greetings to all, We have a Cisco ACI multi-pod (pod 1 & 2) working. We will have a new DC soon and we will have to move our current pod 1 to new location. just wanted to hear experts' ideas on this is it possible to set up new DC as pod 3 and move...
Current setup and situation:We currently have a Mini Fabric deployment (2 virtual APICs, 1 Physical, 4 Leafs, and 2 Spines). One of our engineers accidentally changed the port speed on the uplink interface that connect our Leaf switch and Virtual env...
Hello, In order to create an l2out for my legacy fabric, do I need to create an l2out for every vlan I want to access in the legacy?
Hi ACI professionals,When we decommission a server in our ACI fabric, the fault F0546 is raised (Port is down, reason:sfpAbsent(connected), used by:Discovery). Decommissioning means:- Remove access interface port policy group from leaf interface => ...
We connected an ASR directly to a Cisco Leaf. We are experiencing intermittent slowness with traffic going through the ASR. Should we change the MTU size on the ASR to 9000? Currently, the ASR is at default of 1500 and the Leaf port is at default of ...
