cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
896
Views
0
Helpful
1
Replies

BD Pervasive Route's next-hop

Timothy ACI
Beginner
Beginner

Hi community,

 

What is the next-hop for the pervasive route? I found that it's a loopback on one of my Spines (but not on all 4). Is there a name for that loopback?

 

(Like, there's a loopback for PTEP, a loopback for VTEP that is the same on vPC peer, Spine anycast proxy VTEP, etc.)? I suppose it's the anycast proxy VTEP for v4?

1 Accepted Solution

Accepted Solutions

Sergiu.Daniluk
VIP Advisor VIP Advisor
VIP Advisor

Hi @Timothy ACI 

It's the anycast IP of the spines. Example from my lab:

Leaf101# show ip route 172.16.110.0/24 vrf X
172.16.110.0/24, ubest/mbest: 1/0, attached, direct, pervasive
    *via 10.0.200.66%overlay-1, [1/0], 5d15h, static, tag 4294967294
         recursive next hop: 10.0.200.66/32%overlay-1

Spine201# show ip interface vrf overlay-1 | grep -B 1 10.0.200.66 
lo1, Interface status: protocol-up/link-up/admin-up, iod: 7, mode: anycast-v4
  IP address: 10.0.200.66, IP subnet: 10.0.200.66/32

You can use "show ip interface vrf overlay-1" command to see the names of all IP interfaces on your spines.

Spine201# show ip interface vrf overlay-1 | grep mode:
lo0, Interface status: protocol-up/link-up/admin-up, iod: 6, mode: ptep
lo1, Interface status: protocol-up/link-up/admin-up, iod: 7, mode: anycast-v4
lo2, Interface status: protocol-up/link-up/admin-up, iod: 8, mode: proxy-v4
lo3, Interface status: protocol-up/link-up/admin-up, iod: 9, mode: anycast-mac
lo4, Interface status: protocol-up/link-up/admin-up, iod: 10, mode: proxy-mac
lo5, Interface status: protocol-up/link-up/admin-up, iod: 11, mode: anycast-v6
lo6, Interface status: protocol-up/link-up/admin-up, iod: 12, mode: proxy-v6
lo7, Interface status: protocol-up/link-up/admin-up, iod: 13, mode: anycast-mac,external
lo8, Interface status: protocol-up/link-up/admin-up, iod: 14, mode: anycast-v4,external
lo9, Interface status: protocol-up/link-up/admin-up, iod: 15, mode: anycast-v6,external
lo13, Interface status: protocol-up/link-up/admin-up, iod: 95, mode: dci-mcast-hrep

Stay safe,

Sergiu

View solution in original post

1 Reply 1

Sergiu.Daniluk
VIP Advisor VIP Advisor
VIP Advisor

Hi @Timothy ACI 

It's the anycast IP of the spines. Example from my lab:

Leaf101# show ip route 172.16.110.0/24 vrf X
172.16.110.0/24, ubest/mbest: 1/0, attached, direct, pervasive
    *via 10.0.200.66%overlay-1, [1/0], 5d15h, static, tag 4294967294
         recursive next hop: 10.0.200.66/32%overlay-1

Spine201# show ip interface vrf overlay-1 | grep -B 1 10.0.200.66 
lo1, Interface status: protocol-up/link-up/admin-up, iod: 7, mode: anycast-v4
  IP address: 10.0.200.66, IP subnet: 10.0.200.66/32

You can use "show ip interface vrf overlay-1" command to see the names of all IP interfaces on your spines.

Spine201# show ip interface vrf overlay-1 | grep mode:
lo0, Interface status: protocol-up/link-up/admin-up, iod: 6, mode: ptep
lo1, Interface status: protocol-up/link-up/admin-up, iod: 7, mode: anycast-v4
lo2, Interface status: protocol-up/link-up/admin-up, iod: 8, mode: proxy-v4
lo3, Interface status: protocol-up/link-up/admin-up, iod: 9, mode: anycast-mac
lo4, Interface status: protocol-up/link-up/admin-up, iod: 10, mode: proxy-mac
lo5, Interface status: protocol-up/link-up/admin-up, iod: 11, mode: anycast-v6
lo6, Interface status: protocol-up/link-up/admin-up, iod: 12, mode: proxy-v6
lo7, Interface status: protocol-up/link-up/admin-up, iod: 13, mode: anycast-mac,external
lo8, Interface status: protocol-up/link-up/admin-up, iod: 14, mode: anycast-v4,external
lo9, Interface status: protocol-up/link-up/admin-up, iod: 15, mode: anycast-v6,external
lo13, Interface status: protocol-up/link-up/admin-up, iod: 95, mode: dci-mcast-hrep

Stay safe,

Sergiu

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers