Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Friday, January 17, 2025 through Friday, February 7, 2025. Our colleagues Alex Guckin, Bryan Fenlason, Jason Wiatr, Zuhair Bedwan, Daniel Angelini and Jignesh Sh...
When creating client detail report in DNAC, I would like to add information of buildings and floors for each client. Is it possible to set it like this?
HiI am lab testing multiple SD Access fabrics using one Catalyst Center deployment. At the moment I am deploying an IP transit between each fabric's Borders because I have no requirement to extend SGT's between fabrics.I connect the Borders for each...
Please can someone interpret or convert the viptela commands to cisco IOS sdwan commandsI am planning to replace all our vedges to cisco ISR 1100All our vedges are managed via cli so i need to convert below viptela commands to cisco IOS sdwan command...
Hi,Is it possible to use DNAC (non SDA environment) to report on switches which have a particular config setting.I'm looking to identify any switches in DNAC which have a legacy NTP server set. As DNAC holds all the current configs for my devices I'm...
Hi All,I recently encountered an issue, I do not appear to be able to edit the floor in hierarchy. I am running Version 2.3.7.6-70319.Floor in question requires updated floor plan to be uploaded, this floor has already couple provisioned devices, Fab...
Hi ... I am facing an issue.. I have FHF Industrial Phone that accepts 802.3af (Mode B) and 802.3bt (type 3). I have Cisco IE-3300-8U2X-A with Expansion Module IE-3300-8U2X-A. I have supplied 54VDC as Input to Cisco Switch. I used the command "power...
We are unable to ignore any P1 and P2 critical issues on DNAC, this was working in the past. Attempting this produces an error message 'Error: Request failure while updating issues' Current version of DNAC we are running on is 2.3.5.6-70143 We have c...
Hello,I’m encountering an issue with DNA Catalyst where I’m receiving a compliance error even though the version displayed in the Golden Image matches the running version.Details:Golden Image Version: 17.12.04SMU Version: 17.12.04Running Version: 17....
Since configuration is done through Catalyst Center, is there a way to limit access for a user to just configure an AP and not be able to configure the WLC in ways that can take down the hole wireless network? To give a user access to configure an ...
We have DNAC deploy but need to change a route as we cannot access DNA gui from a specific subnet.Running the maglev-config update I get an error / warning.Remove all NFS mount before network changes.Cannot find a process anywhere to sot this out. TI...
Hello,Some of you may think me crazy but let me ask. We came into the office this morning to find several Change Alerts from our SNMP Monitor. They Centered on our Catalyst 9200 switches. Apparently, the Bluetooth interface has been introduced to our...
Hello I am getting several errors in the log for a weak RSA keythe error as shown is %CRYPTO_ENGINE-4-CSDL_COMPLIANCE_RSA_WEAK_KEYS: RSA keypair CISCO_IDEVID_CMCA_SUDI is in violation of Cisco security compliance guidelines and will be rejected.When ...
Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Friday, January 17, 2025 through Friday, February 7, 2025. Our colleagues Alex Guckin, Bryan Fenlason, Jason Wiatr, Zuhair Bedwan, Daniel Angelini and Jignesh Sh...
Hello Everyone,In our data center, we are currently using a 3850 as our internet switch, what is the best replacement for it within the $2.5k to 3k? It should support layer 3 routing. Thanks
Hi All, We have a DNAC DN-SW-APL installed inside VMware ESXi. Currently, the admin account details are missing due to an improper handover. We have retrieved the Maglev username and password; however, when trying to log in to the GUI using these cre...
