Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Friday, January 17, 2025 through Friday, February 7, 2025. Our colleagues Alex Guckin, Bryan Fenlason, Jason Wiatr, Zuhair Bedwan, Daniel Angelini and Jignesh Sh...
Hi Team,Is it possible to integrate UBUNTU DHCP server with DNA center for IP address Management. Under IP address Manager- there are three options Infoblox, Bluecat and Generic. can we use Generic ?. Regards,Raj
We have 8300 routers which were provisioned in DNAC. We'd like to push Telemetry to them but can't get it to work. When I hover over the Information Icon to get information about why its Not Provisioned it says Could not parse [ ]I have a TAC call op...
I am trying to upgrade to 2.2.2.3 but I get an error message that the are packages in the process of downloading and I can only start the upgrade once those packages have been completed. The packages remain on 30% and 60% now for days! I have tried t...
We are in the process of building our SD Access Lab. We have a 2nd Generation DNA Appliance (UCS C220 M5) that shipped with DNA Center 1.3.0x. Following the initial interview to get the base configuration on it and then logging onto the Web GUI we ...
Hi Team,I have DN2-HW-APL DNAC 2nd generation physical hardware, al few devices which are DNA ready and capable of supporting DNAC. Do i need to install any additional License on the DN2-HW-APL hardware (Wireless Subscription/Switching Subscription)?...
Hi All, The company I work for provides bespoke computing systems. We have previously been supplying Cisco 2960 series switches which form a very basic network. PC A connects to Switch APC B connects to Switch BSwitch A and Switch B are interlinked. ...
Hi,I have just upgraded my DNAC verison 1.3.3.7 to version 2.1.2.7.Under provision and inventory I have a box the some fixes the DNAC want to apply.One of them says: "We detected IOS-XE device(s) in your network where new telemetry subscription for a...
Have been looking for a way to use DNA to scan the configuration of managed devices to check for ISE level port commands. Is this possible?
Hi We have scenario in a standard topology ( 2Xborders - 2 X intermediates - 2XEdge stacks) with full mesh connectivity, both edges are connected to both intermediates. We are provisioning switches thru LAN Automation (DNAC Version 2.1.2.5). we had t...
Hi,Trying to automate the whole process of migrating a branch to SDA. I seem to be missing some calls though, that are important to get the whole way. Version 2.2.2.3. How do i provision a device once discovery is done? I can assign to site, but not ...
Dna GUI not loading getting the below error {"message":"no route and no API found with those values"}servies are running please find the below screen i have tried on physical and virtual both same error .
Hi everyone, May I know how I can enrol Mentorme Program, is there any email I can contact? I just heard about this helpful program. But the application is already closed. I really hope I could get chance to enrol this program. I am doing my 2nd se...
Hello community,I have an issue with adding a static route to cisco dna center, because I made a mistake when configuring the cisco dna center ports, we have added the static route to thedna management port and we forgot to add a route to enterprise ...
Hi all we are testing a wireless sensor with DNAC.All test go well, but we stil have reported failures under association.If I drill down, the failure reason is "Deauthenticated because Sensor is leaving" (see screenshot)Isn't this normal behavior?
Working to automate the build of a C3560CX and managed to get things working to the point where a golden image was pushed to the unit and a base config pushed out from template. All good. Then proceeded to delete the device from DNAC, run a 'pnpa sy...
