cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Amit Sharma
Cisco Employee
Cisco Employee

Port Calculation for CUE 7.1 and later

Common error message:

CUE8-0-1# show license status application

voicemail disabled, ivr session quantity (8) is equal to or exceeds

available ports (8)

ivr enabled: 8 sessions

IVR sessions reduce the number of sessions available for VM.

VM Sessions = Ports minus IVR Sessions.

If Ports = 8 and IVR Sessions = 8 then VM Sessions = 0

Majority of the users do not use IVR features so you may not install and/or activate an IVR license.

Please issue 'license activate ivr sessions N' where N should be 0, 2,

or 4 or 6 so that voicemail will get 8-N sessions, then issue 'reload'.

For installing/upgrading the software on ISM-SRE/SM-SRE modules:

These new modules offer to install the files directly form the router's interface.

You need not session in the CUE's inetrface.

Syntax:

service-module sm slot/0 install url url [script script-name] [argument argument] [force]

Examples:

1.Router(config)# service-module ism 0/0 install url ftp://username:password@128.107.146.189/dir/cue-vm-k9.sme.7.1.2.pkg script cue-vm-k9.sme.7.1.2.sre

In case of anonymous configuration on the FTP

2.Router(config)# service-module ism 0/0 install url ftp://128.107.146.189/cue-vm-k9.sme.7.1.2.pkg script cue-vm-k9.sme.7.1.2.sre

For fresh installation the file to be installed first is

The package file to install is cue-vm-k9.sme.7.1.2.pkg

Make sure the rest of the files are stored in the directory mentioned in the URL above:

cue-installer.sme.8.0.x

cue-vm-k9.sme.8.0.x.pkg

cue-vm-full-k9.sme.8.0.x.prt1

cue-vm-installer-k9.sme.8.0.x.prt1

cue-vm-langpack.sme.8.0.x.prt1

The lang .pkg file you wish to install.

Link for detail information:

Installing Cisco Unity Express 8.0 Software on Services Ready Engine (SRE) Modules:

http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel8_0/install/installsre.html

For activating the permanent license:

In some cases even though the permanent license has been installed, the show license in use would show up the evaluation license.

CUE8-0-1# show license in-use

StoreIndex:  4  Feature: VMIVR-PORT                        Version: 1.0

        License Type: Evaluation

        License State: Active, In Use

        License Count: 8 /8

        License Priority: Medium

StoreIndex:  5  Feature: VMIVR-IVR-SESS                    Version: 1.0

        License Type: Evaluation

        License State: Active, In Use

        License Count: 2 /2

        License Priority: Medium

StoreIndex:  7  Feature: VMIVR-VM-MBX                      Version: 1.0

        License Type: Evaluation

        License State: Active, In Use

        License Count: 105 /5

        License Priority: Medium

Please run the following command and reboot the CUE:

CUE8-0-1# license modify priority VMIVR-IVR-SESS low

Similarly for all the other features

After the CUE is rebooted the CUE would boot up with the permanent licenses.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Quick Links