cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5075
Views
0
Helpful
13
Comments
Teck Chye Tang
Cisco Employee
Cisco Employee

The attached document details the method and procedure to load the TC series software to the codec from scratch.  Document is written based on the used of Cisco TFTP server v1.1 (http://www.brothersoft.com/cisco-tftp-server-220729.html)

Requirements:

a) TC software

b) TFTP server

c) Serial cable

d) u-boot.bin file (attached)

e) pkgextract.elf file (attached)

Applicable to the following codec (as of now) :

a)     C20

b)     C40

c)     C60

d)     C90

e)     EX60

f)      EX90

g)     MX200

h)     MX300

i)      SX20

Comments
Not applicable

Hello, I think pkgfiles_uboot.rar.zip is for C40 or else, because then try make this for my C20 - get error.

Press 'b' to enter u-boot prompt

Press 'c' to stop autoboot:  4

ORION> setenv serverip xxx.xxx.134.206

ORION> setenv tftp_path pkgfiles

ORION> setenv orionpkg s52000tc2_0_1.pkg

ORION> run pkgex

BOOTP broadcast 1

DHCP client bound to address xxx.xxx.134.209

NAND erase: device 0 whole chip

Skipping bad block at  0x09b40000

Skipping bad block at  0x0ea40000

Skipping bad block at  0x27640000

Skipping bad block at  0x48700000

Skipping bad block at  0x4d980000

Skipping bad block at  0x582c0000

Skipping bad block at  0x7cb40000

Erasing at 0x7ffc0000 -- 100% complete.

OK

yaffs: Mounting /flash

Using TSEC0 device

TFTP from server xxx.xxx.134.206; our IP address is xxx.xxx.134.209

Filename 'pkgfiles/saturn.pkg'.

Load address: 0x2000000

Loading: *

TFTP error: 'File not found??f•wabcdefghi??×ö' (1)

Not retrying...

Copy pkgextract.elf from NOR flash to 0x1000000

## Starting application at 0x00042e78 ...

Buildtime: Jan  4 2012 11:31:59

Not a PKG file (170173190)

Failed to read PKG header

## Application terminated, rc = 0x1

image1 is not a directory

Reprogram NOR from /flash/image1

Un-Protected 1 sectors

. done

Erased 1 sectors

Copy /flash/image1/bootsw to 0x01000000... File not found

Write /flash/image1/bootsw (4294967295) to NOR flash

NOR allready contains correct data

Copy /flash/image1/pkgextract.elf to 0x01000000... File not found

Write /flash/image1/pkgextract.elf (4294967295) to NOR flash

NOR allready contains correct data

File /flash/image1/S01710.bin.wrapper not found

ORION> Orion

Unknown command 'Orion' - try 'help'

ORION>        SN: F1AN2

Unknown command 'SN:' - try 'help'

ORION>        SN: PB039 TSEC1

Unknown command 'SN:' - try 'help'

ORION> Hwmon: 43

Unknown command 'Hwmon:' - try 'help'

ORION> Press erverip 210tc2_0_1.pkg

Unknown command 'Press' - try 'help'

ORION> ORION> run pkgexe: device 0 whole chip

Unknown command 'ORION>' - try 'help'

ORION> Skipping bad blox27640000

Unknown command 'Skipping' - try 'help'

ORION> Skipping bad blo582c0000

Unknown command 'Skipping' - try 'help'

ORION> Skipping bad blo/flash

Unknown command 'Skipping' - try 'help'

ORION> Using TSE0 device 'pkgfiles/saturn.pkg'.

Unknown command 'Using' - try 'help'

ORION> Load address: 0xretrying...

Unknown command 'Load' - try 'help'

ORION> Copy pkgextract.Buildtime: Jan  4 2012 11:31:59

Unknown command 'Copy' - try 'help'

ORION> Not a PKG file (image1 is not a directory

Unknown command 'Not' - try 'help'

ORION> Reprogram NOR frlash/image1/bootw to 0x01000000... File not found

Unknown command 'Reprogram' - try 'help'

ORION> Write /flash/imaflash/image1/pkgextract.elf to 0x01000000... File not fou

nd

Unknown command 'Write' - try 'help'

ORION> Write /flash/imadata

Unknown command 'Write' - try 'help'

ORION> File /flash/imag

Teck Chye Tang
Cisco Employee
Cisco Employee

ORION> setenv orionpkg s52000tc2_0_1.pkg .......

The above command should be setenv saturnpkg s52000tc2_0_1.pkg....

no need to change the name to that of the codec used.  Just leave it as saturn.

Still same error. There is Log:

ORION> setenv serverip xxx.xxx.134.247

ORION> setenv tftp_path pkgfile

ORION> setenv saturnpkg s52000tc2_0_1.pkg

ORION> run pkgex

BOOTP broadcast 1

DHCP client bound to address xxx.xxx.134.214

save exit: isCheckpointed 1

NAND erase: device 0 whole chip

Skipping bad block at  0x09b40000

Skipping bad block at  0x0ea40000

Skipping bad block at  0x27640000

Skipping bad block at  0x48700000

Skipping bad block at  0x4d980000

Skipping bad block at  0x582c0000

Skipping bad block at  0x7cb40000

Erasing at 0x7ffc0000 -- 100% complete.

OK

yaffs: Mounting /flash

Using TSEC0 device

TFTP from server xxx.xxx.134.247; our IP address is xxx.xxx.134.214

Filename 'pkgfile/s52000tc2_0_1.pkg'.

Load address: 0x2000000

Loading: *

TFTP error: 'File not foundô"…2' (1)

Not retrying...

Copy pkgextract.elf from NOR flash to 0x1000000

## Starting application at 0x00042e78 ...

Buildtime: Jan  4 2012 11:31:59

Not a PKG file (170173190)

Failed to read PKG header

## Application terminated, rc = 0x1

image1 is not a directory

Reprogram NOR from /flash/image1

Un-Protected 1 sectors

. done

Erased 1 sectors

Copy /flash/image1/bootsw to 0x01000000... File not found

Write /flash/image1/bootsw (4294967295) to NOR flash

NOR allready contains correct data

Copy /flash/image1/pkgextract.elf to 0x01000000... File not found

Write /flash/image1/pkgextract.elf (4294967295) to NOR flash

NOR allready contains correct data

File /flash/image1/S01710.bin.wrapper not found

I think the reason of this error can be - not correctly working Cisco TFTP server, because it dont show any Logs, any activity then try upload software.

Maybe I do something wrong.

I set for Cisco TFTP server root address (C:\Program Files\Cisco Systems\Cisco TFTP Server\pkgfile). Maybe need make some more in this?

C:\Program Files\Cisco Systems\Cisco TFTP Server\pkgfile
John Regan
Level 1
Level 1

Hello,

You are trying to load TC2.0.1 for some reason (s52000tc2_0_1.pkg).  C40s only support TC3 as minimum and I would recommend that you uploaded a more recent version than that.

This will not help you file not found message but trying to upload TC2.0.1 will not help you.  What files do you have in your pkgfile directory?

Thanks

John

Hello, I try upload software to our Tandberg C20 demo.

in pkgfile directory is this three files:

s52000tc2_0_1.pkg

pkgextract.elf

u-boot

The command to start upload is this:

setenv serverip xxx.xxx.134.247

setenv tftp_path pkgfile

setenv saturnpkg s52000tc2_0_1.pkg

run pkgex

Teck Chye Tang
Cisco Employee
Cisco Employee

setenv saturnpkg s52000tc2_0_0.pkg, is this s typing misake?  should be s52000tc2_0_1.pkg

Suggest you run through this with a TAC's help to see if everything is done correctly.

Else, codec might really be having an issue.

Hi again, I uploded software sucessful - Just install SolorWind TFTP server and everything become good. So Thanks for help

Hes
Level 1
Level 1

Is there also such a process for the E20?

I only have image1 and not image2, this seems to be corrupted.

Image1 has an unknown password (admin and root account password unknown).

** Presentation ## doesn't work

Switching images by pressing 4 and 6 obviously doesn't work also, I only get the SNOOPY> prompt then.

Just being able to reset the password would be fine too...

Hes
Level 1
Level 1

Managed to log in as root now and deleted config.db to reset the password.
Seems that Putty didn't understand my breaks and had to use the menu for this.

Upgraded and now have two images again.

Not applicable

Still having issue with errors can't get karnel image, what can i do?

Daniel Ruiz
Level 1
Level 1

Good Afternoon I have an issue with my tandberg c90

At the start in "SATURN>" I see "SATURNII>" and not allow me to install the computer software any thoughts on this??

Daniel Ruiz
Level 1
Level 1

I get the following on startup

#####################################################################################################

#####################################################################################################

SATURNII>

U-Boot 2010.06-107 (Sep 28 2012 - 08:20:46) MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_EA, Rev: 3.0 at 600 MHz, CSB: 200 MHz

I2C:   ready

DRAM:  DDR2 RAM: 512 MiB

RAM data bus test       [PASS]

RAM address bus test    [PASS]

FLASH: 4 MiB

NAND:  2048 MiB

RTC:   2013-07-26 (Friday) - Time: 19:33:08

PCI Video Processor Detection   [PASS]

Saturn main board

        Rev: G

        SN: PH1194576

        Object level: 33

        MAC: 00:50:60:84:0F:EF

SaturnII video board

        Rev: G

        SN: PH1195215

        Object level: 10,12

Saturn audio extension board

        Rev: E

        SN: PH1194502

        Object level: 04

Net:   TSEC0, TSEC1

Hwmon: 45

Eth:   Configure the external switch

Press 'b' to enter u-boot prompt

Press 'c' to stop autoboot:  0

yaffs: Mounting /flash

yaffs: restored from checkpoint

Configure FPGAs

FPGA configuration failed

Setting up Davinci HD (01.00.00)... 675Mhz       [DONE]

Setting up Davinci HD (01.01.00)... 675Mhz       [DONE]

Setting up Davinci HD (01.02.00)... 675Mhz       [DONE]

Setting up Davinci HD (01.03.00)... 675Mhz       [DONE]

Setting up Davinci HD (02.00.00)... 675Mhz       [DONE]

Setting up Davinci HD (02.01.00)... 675Mhz       [DONE]

Setting up Davinci HD (02.02.00)...1000Mhz       [DONE]

Setting up Davinci HD (02.03.00)...1000Mhz       [DONE]

Setting up Davinci HD (02.04.00)...1000Mhz       [DONE]

Setting up Davinci HD (02.05.00)...1000Mhz       [DONE]

Copy /flash/active/arm/rootfs to 0x03000000... File not found

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Copy /flash/active/arm/kernel to 0x02000000... File not found

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Copy /flash/active/arm/u-boot.bin to 0x01000000... File not found

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Error: filesize must be > 0

Copy /flash/active/kernel to 0x01000000... File not found

Copy /flash/active/rootfs to 0x02000000... File not found

Copy /flash/active/dtb to 0x03000000... File not found

save exit: isCheckpointed 1

Wrong Image Format for bootm command

ERROR: can't get kernel image!

SATURNII>

MinyuVV_14
Level 1
Level 1

Please help to resolve the boot failure with sx20

ASTERIX> run pkgex
## Error: "pkgex" not defined

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: