Collaboration, Voix et Vidéo

recherche de prise dc pour cisco 8945k9

Bonjour ,j'ai ecrasé ma prise dc de l'alimentation de mon téléphone cisco 8945k9 de ce fait je recherche cette prise pour nous en France c'est dans le domaine de l'impossible .Quelq'un peut me donner les cotes ou la prise merci d'avance

SIP TRUNK incoming and outgoing calls with CME fails

Hello everyone, I want you to help me with a configuration. I have a cisco ISR 4321 router that acts as both CME and CUBE for the SIP TRUNK gateway to the provider’s network. Configurations have been made in such a way that the authorized extensions ...

Résolu! Phone no register

Hello everyone, i have a problem with my cisco 8200 router series ( IOS XE 17.6.x ) , i try to configure it in mode CME , but the phones do not register ?may be a licence problem ?here's my configuration :Building configuration...Current configurati...

caller ID display on Cisco Finesse and Jabber

Hello everyone,I have a question regarding caller ID display on Cisco Finesse and Jabber.Currently, incoming calls from a queue in Finesse are displayed as "call center" on Jabber, without showing the caller’s number. I’d like to know if it’s possibl...

SIP TRUNK between CUCM and CMS

Dear,I have a sip Trunk between cucm and cluster of cms .the problem is that the trunk link is not stable , from time to time (no more than 7 minutes) the SIP trunk status is switched to "no service"Could I have a help from you.

Issue with Agent List Not Automatically Refreshing in Webex CC Desktop

I am writing to report an issue I am facing with Webex Contact Center Desktop. The list of agents does not refresh automatically, and I am required to manually refresh the interface each time to see the current status of the agents. This is causing d...

Cisco DX80 et ZOOM meeting

Bonjour Nouvel utilisateur d'un Cisco DX80, et novice, j'aimerais l'utiliser pour rejoindre des sessions de réunion Zoom. La version est Room Os CE 9.15.17... etc. et mon abonnement Webex est "Gratuit". L’accès à Control Hub Webex pour ajouter cette ...

Honoré d'être Technical Reviewer d'un livre sur Cisco Collaboration

Je suis ravi et honoré d’être le technical reviewer du livre intitulé "Cisco Collaboration Infrastructure for Enterprise Solutions," écrit par un expert CCIE collaboration avec AVA™ - An Orange Education Label. En tant qu'auteur passionné ayant publ...

How do to find out the dscp range with DSCP Wildcard Mask in an ACL ?

Hi, in the exemple below it says the range for dscp value 30 with dscp-mask 30 is 33 through 63.How do you calculate the range for the dscp mask? Do you just add 30 to 33 ? ExampleIn the following example, an ACL looks at traffic that is sent from su...

CUCM 12.5 "No applications have been installed."

Hi, for a few weeks I have been facing this error "No applications have been installed." on my cucm at version 12.5 when I try to go to the ccmadmin interface. After my research, I read that it was a recognized bug, but I couldn’t figure out how to f...

Cisco VOIP Technologies

Hello,I'm new to learning VOIP on Cisco phones, and I'm having trouble finding clear information about the following Cisco technologies:Cisco Unified CM (CallManager) PUB SUBCisco Unity Connection Administration PUB SUBCisco Unified Attendant Console...

DRF local and master down

Hiwhen i launch cucm backup manual to UCM,IM&PR,and CDR it stuck and say failed to initiate backup after i restart them (services DRF) in sub and pub, if select only CDR it success, same for IM&PR and UCM but if select all (three) it stuck in 51% and...

Résolu! set router as ntp server and port 123

Hi i have router cisco gw voice 4400, and cluster CUCM 12.5 PUB and SUB, i want to set router as server ntp with ntp server master 1, after i want to associate cluster with this ntp server (utils ntp server add ip router it gives me error not add), i...

CMS and CUCM compatibility

Hello, I plan upgrading my CMS version for 3.7 to 3.9.1. I can't find the minimum CUCM version required for 3.9.1 version

Call and Share Buttons appearing along bottom of screen

Hi,We have multiple cisco room kits ranging from mini to Plus at a number of our client sites. We are having this issue where some the call and share screen buttons are appearing on the main display as well as being on the touch panel. I've been thro...

Collaboration, Voix et Vidéo

Parcourir la Community

Discussions de Vidéo

Discussions de VoIP

Documents de Collaboration, Voix et Vidéo

Blogues de Collaboration, Voix et Vidéo

Vidéos de Collaboration, Voix et Vidéo

Activité dans Collaboration, Voix et Vidéo