Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear All ,We had a new Voice Gatway router C3945-CME-SRST/K9 for our new branch ,I did basic configuration like configuring Gatway ,configuring Dial Peer .can any one provide me the steps for Configuring Voice Gateway .Thanks.,Mubarak Ali
I have one user who reported that when he use the IP Phone to dial to another site office, the other party cannot hear his voice.It happens only for certain calls to the same site office, some can hear his voice but some cannot.How do I troubeshoot t...
Hi AllWe have a issues wiht one of our cutomer that when enduser press Voice Mail button to access the VoiceMail it then sometimes keeps ringing and then call gets hanged up/disonnects. its intermitten issue...has any one come accross this /any idea...
Hi all,Nee you assistance, can you please let me know how to check the CUCM is working fine? quick reply would be appreciated. thanks.
Hi All,I'm after some advice on a dial plan design for a new CUCM depoyment. There will be about 20 global offices with a total of 5000 staff connecting to a single CUCM cluster in the USOne of the biggest challanges that I have is making sure ...
I am looking for information the right type of wic to use to support isdn voice calls off of Call Manger for isdn brodcast equipment. We currently planing out a migration from another vendor's product which prodives a two wire isdn U interface. I nee...
We had an incident where our users couldn't make outbound calls. However, we could receive inbound calls. What we had to do is teardown the MGCP (no mgcp) and restart it. From the CUCM, the Route List were registered, the gateways were registered....
Hi ,I need quick help to forward all calls to respctive number.requirement:I want forward all calls when user pickup receiverwe are connected phone to FXS port in router and router configured as aMGCP gateway.I given command connection plar ...
Hello,There is a CUBE (12.4(25c)) with SIP trunk to telco on public IP. CUCM is connected to CUBE with SIP trunk to private IP on loopback interface. Though the default behavior for media to flow through in voice service voip and dial-peer configurat...
We have MCS7835-H2s running CUCM 6.1(3b)SU1. We want to upgrade to 8.6. Looking at the compatibility charts it looks like these servers are supported for a bridge upgrade only. But if we upgrade the memory to 4 GB and the hard drives to 146 GB wou...
Hi,When i place a internal call from CME to a CUCM, the ipphone 6921 ask me to press softkey ´acct´ , if I dont press anything drops the call, in order to place the call i need to press ácct´ and the * I have configurated a fac custom pickup group an...
Hi all,I have configured a cisco 7911 with the following configurations:ephone-dn 40 dual-line number 999 no-reg both label Faith_Test 999 name Faith_Test corlist incoming In000-002-98 huntstop channelephone 40 device-security-mode none mac-addres...
Hi allI have a question the CCM 4.3 support windows 2000 or not ?because I have a CCM 4.1 with OS windows 2000 and I want to upgrad it to CCM 4.3.Thanks and kind regards.
Hi All,I have an issue with our iPhone jabber clients with CME. The issue was first brought to my attention as users couldn't log into their CUE voicemail. They would dial the mailbox extension, get the prompt to enter their mailbox number and press ...
Hello, I am trying to get either of our in office 6921 or 6945 phones to transfer. In most cases as soon as you hit the transfer button it puts the person on hold then you type in the extension to which you are transfering, then hit the button again ...
