Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,Ho to connect a CCM6 with a router that use an interface card configured with a E1 PRI Signaling.The gateway protocol is MGCP.I've tryed to configure it, but, I've not seen a R2 signalisation.I just see : PRI EURO, PRI ISO QSIG E1, PRI AUSTRALIANW...
Hi,Just getting ready for some heavy VG224 roll-outs, and getting BAT working properly to automate adding the gateways.All is going OK, apart from the minor problem that the directory number is not assigned to the port if the number already exists in...
Is there any way for a user to login to different line groups (at different times) from their phones? Aside from the admin moving them into different groups, I need a way for a user to move themselves into different line groups. Thanks for the help...
Using Extension Mobility on CUCM6 seems to create problems when using DNA. If you select "Phone" in DNA and search for a user who is a EM and is logged into a handset but not associated to it which is normal for EM then DNA does not allocate the user...
Hi i have two callmanager pub and sub running 5.03 cm.The active partition on the callmanager sub is showing no free disk space.Also the DRF services now fail to start aswell as the CDRRepository manager.I have checked replication and that is fine.Wh...
We recently upgraded to CM 6.1.2. We are currently using the internal database for the corporate directory. I know with 6.1.2 there have been a lot of LDAP enhancements. My question is that if I enable LDAP synchronization, will it overwrite my cur...
Hi,Just curious if anyone has run into this or what might be the cause. I am told it is an internal dialed number from a remote site, cme to cme I believe..... After 5 minutes on call, goes to one way audio.
Hi, in our CCM cluster, various cisco services in services.msc on ccm servers are started using different local user accounts. screenshot attached. Can anybody tell me what could be the purpose behind this?
Does anyone know how licences are used in IPCC 4.5?ICR port 150standard 69Maximum 300?does this mean 69 are used from 300 allocation?Found in control management - under licence informationany ideas - many thanks
I have setup a sip trunk between my call manager and cme. I can call any phone from CUCM to the CME. When I try to place a call from CME to CUCM I am getting a fast busy. Here is by SIP Trunk on the CME sidedial-peer voice 1003 voip destination-pat...
this conversation should be in this area, sorryIP Phone Services for End Users: LLDP suport for 7940 and 7940GPosted by: tjandrew2304Jul 17, 2008, 1:01am PSTIve got an install going on with my old phones that I need to support LLDP on the older 7940 ...
We have a new voice design in the testing phase, where the traffic path was shown below. This setup was working: Verizon-->Edge_Router-->IP2IP Gateway-->Call Manager The IP2IP Gateway router was sitting with a single ethernet interface on the core sw...
HelloI know for CCM5.1.3 it's possible to assign a phone button template on the device default phone type.Basically this is based on buttons you would like to assing for auto registered phones.I would like to add the phone-service such as Extension M...
Hi all. Im looking at Presence again, and trying to just figure out a few things. Yes, Im very new to Presence, so Im trying to figure out what is best for the customer at this point. So, my questions are the following:1. What benefits does it gi...
Hello I am trying to implement IP phone solution over an IPsec tunnel to no avail. The phone is stuck on Configuring IP eventhough the DHCP server assigned and address to the phone please HELP!!!!
| User | Count |
|---|---|
| 10 | |
| 3 | |
| 3 | |
| 1 | |
| 1 |
