I am needing to know how to disable drive locate function as I am getting a flashing Amber LED on my drive. I am running version 3.1 on my SNS-3615, also my system health LED is steady Amber. This all started after I upgraded to 3.1.
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.
Forum Posts
Resolved! ISE Backup and Restore Question
Hello Community,I am in the process of upgrading our ISE hardware from SNS-3595-K9 Version 2.7 to SNS-3755-K9 Version 3.1 and I am at the point where I will be restoring the data to our new environment from the shared repository we have set up that r...
Hey gang! I'm running into a strange deployment issue in my lab. Using ISE 3.2 Patch 4. The primary server is running fine as PAN/PSN/MNT. When I try to add a secondary server to the deployment, it is added successfully and the status of the new ...
Hey guys!I am studying a demand to enable smartphone authentication on the BYOD network, with authentication via EAP-TLS on Cisco ISE.I have experience in previous projects, where I configured EAP-TLS authentication for computers, which received a pe...
Hello All, My understanding of Monitor Mode is that the switch (in our case)makes the authentication request to the Cisco ISE, but it ignores the result and provides access to the network. We had the experience that when a policy was created that ret...
Resolved! Wied 802.1X Using Certificate
We are looking to implement wired 802.1X, but we would like to use a certificate to authenticate so that users do not have to authenticate, especially on desktops shared by staff. We tried to implement this using PEAP with EAP-TLS for the inner tunne...
Hello!We have:- ISE 3.0.0.458- AnyConnect- ASAUsers connect with AnyConnect to the corporate network using a certificate. On ASA - We take the attribute CN from it (username-from-certificate CN).Example: CN - Ivan Ivanov. During authentication, ISE s...
Hello, I'm struggling to find a way to indicate to registered guest users why their authentication fails at login. For example, the guest account may have expired; however the only error message displayed is 'Authentication failed'. Other reasons may...
Ok, so this alarm is coming in repeatedly and is now on my projects list. I get email alerts from the server that list thr NAD IP as the endpoint device and the Endpoint IP address is correct. I've checked the settings and the endpoint is not liste...
Hi everybody;According to Cisco's documents, if a port is defined in "Common Ports", when you want to add it again to the "Custom Ports" section, the "Port is predefined" error message appears (as shown below). In other words, you cannot use the same...
We are about to implement AAA/TACACS admin authentication for switches on our remote site and we need to make sure that once we paste the script that we do not loose access to the remote switch. is there any tips on doing this without loosing access ...
Resolved! Enable SSH
How do I enable SSH?
Hello Everyone,While trying to generate certificate using Certificate Provisioning Portal, I'm getting the following error : I thought I might be running into bug : https://bst.cisco.com/bugsearch/bug/CSCwa03797But even the workarounds aren't working...
Resolved! pxGrid - 503 Service unavailable
Hi, I'm trying to create an account for the integration in pxGrid of the Palo Alto's TrustSec plug-in but I'm getting an error saying that the service is not available. This is the first pxGrid client I'm registering in ISE. I run a diagnostic tes...
Hello,I am trying to build a Visitor Kiosk portal so a visitor can register themselves and get their guest credentials. I have something kind of working using scripting (this uses a guest portal which is normally used as a redirection URL). However, ...
