Network Management

EEM Ping several destinations Script

Dears, I need help to figure out what is wrong with my EEM applet script : Am in need to send by mail the result of ping to different destinations, the script is as below: event manager session cli XXXX event manager environment _email_from XXXXXeve...

Converting my AutoSmartPort to EEM - Match VLANS on MAC IF/ELSE

I have the below ASP config. But I'm trying to do much more. I've read through a lot of threads on this community but I still can't seem to get it to work. macro auto execute SKYPE_OUI_MATCH { if [[ $LINKUP == YES ]] then conf t default interf...

Resolved! Prime Infrastructure 2.2 maps tree view empty

hi, As it says in the title my "maps tree view" is empty. I've tried saving the configuration and restarting ncs but it has stayed blank. best regards Peter

Resolved! Cisco Prime 3.1 Email Customization

Hello, We configured email alerts in Cisco Prime 3.1 and it is working. although I cannot find the option to customize the Email subject and body. Any advice is appreciated

Resolved! CISCO ISR 819 LOW SIGNAL FAIL OVER with EEM SCRIPT

Hi All, I was trying to do a EEM scripting for Cisco 819 for Low signal threshold with this applet: event manager applet watch-signal event timer watchdog time 60 maxrun 120 action 001 cli command "enable" action 002 cli command "show cellular 0 ra...

ssh key does not match known_hosts

On an IOS-XE device, I compared the ssh key from "show ip ssh" with the key for the device stored in my known_hosts file, and I notice that key on my server has an additional two characters than what is listed on the switch. Anyone have any idea why ...

Cisco Prime 3.1 - Link down alerts

Hello, I started receiving these alerts from Prime for multiple switches in our network: PI has detected one or more alarms of category Switches and Routers and severity Critical in Virtual Domain ROOT-DOMAIN for the following items: 1. Timestamp: ...

Adding Links between the switches manually in Cisco PI 2.2

Hi, Currently, I am working on Cisco Prime Infrastructure 2.2. I have around 20 remote stations that are connected to the core switch through SDH. In topology, I am assigning Links manually and interfaces as well. Is it possible that I can assign...

AM/PM vs 24-Hor

Hi, Can anybody tell me how I move from AM/PM to 24-Hour format for the Cisco PI 3.3 ?? :D I'm lost.

SNMP OID for CPLD Version - ISR 4000

Hi, I know how to get values for IOS version and ROMMON version, but CPLD version on the other hand I can't see how you can collect via SNMP. Any suggestions? Thanks. /JZ

ASA 5506-X, FirePower, can't change system policy

Hello!I have an ASA5506X with FirePower, version 6.2.2.1 (Build 73). I can't change the Default System Policy. I have got the Invalid object type error (see attached screenshot). Does anybody have an idea what causes of this error ?

Specific MIB to find SFP connector and its current state

I'm trying to find a way to get the current state of a Cisco Catalyst Switch (2960S, with version 12.2(55)SE3) and its SFP ports, by polling with SNMP. At the moment I'm using a software called OidViEW and MIB "MIB CISCO-IF-EXTENSION-MIB:"Where im lo...

Export Physcial Port MAC Addresses from Prime

I need to gather all of the MAC addresses from my switches physical ports and have found through Prime that it does track that, but I would like to export that into a spreadsheet and I do not see anywhere where that is an option. I went to Device Det...

Resolved! Cisco Prime 2.0 doesn't start

Hi, I have recently joined the NHS and we have a Cisco Prime NCS running 2.0 that doesn't start. IT IS NOT UNDER A SUPPORT CONTRACT. I'm trying to get this thing working and have hit a road block. There is an inbuild account in the NCS database tha...