Hi I am learning about advanced EIGRP and have made the following notes for advanced features that can be implemented , would somebody kindly pass comment on if I have missed anything or if theres any other advanced features I can configure as part o...
Forum Posts
Hello everyone,I need to query the AP9120 via SNMP to retrieve the device name. We are using a Linux server located in a different subnet for the query.The WLC is a 9800 model with SNMP enabled. When I query the WLC, it responds with its name, but wh...
Hello,Anyone know which ios minimum version to create EEM script?I can see in this article Cisco IOS Embedded Event Manager Command Reference - E through event manager Commands [Support] - Cisco the minimum version is 12.2I have C2960X running versio...
Resolved! asa 5515 ios image deleted
I deleted all disk in ASA 5515 so I lost my IOS image unfraternally I can't get the ROMMON. the system gets this message> " Password recovery and ROMMON command line access has beendisabled by your security policy. Choosing YES below will cause ALLco...
Hi, I'm currently trying to make a CISCO_ASR1002:Cisco IOS XE Software, Version 03.16.06.S - Extended Support VersionCisco IOS Software, ASR1000 Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.5 (3) S6, LAUNCH SOFTWARE (fc3)Send CGNAT transla...
Hi all!I am trying to configure a collapsed layer network architecture. I configured HSRP and L3 switches sees each other with no problem (sh standby br is OK) but when I configure a PC in VLAN10 and give default gateway as the HSRP virtual IP to it,...
I have a problem with NX-OS and i am trying to initiate the following command to filter output of "show cdp nei det"this is how i would done on 6500show cdp nei det | grep Device |IPv4 Add|Cisco IOS SoftwI need this to work on NX-OS.. I noticed lots ...
Hi Geeks, I have a crashed 2960x switch and I am trying to upgrade the ios, when transferring file thru console flash is full.I cannot delete file or directory. below are the errors I got when deleting. switch: rmdir flash:/c2960x-universalk9-mz.150-...
Hello Everyone, after an OS-Update from 16.12.4 to 17.12.4 on Catalyst 9300L, we are not able to get the same PRTG-Monitorung results.For Example smart licensing:we have four Sensors setup, but with 17.x we only get response to one Sensor.ciscoSlaEna...
Hello,I have a Cisco switch connected at L2 and want two L3 vlan interfaces for management. Each VLAN is on a different vrf. The issue is we can only specify one Default gateway so we can't get full connectivity for both. We cannot leak routes from o...
The CPU of the core switch has abnormally increased, and the sorting of the query process does not show the highest CPU content on this side of the record.The command I used was show processes CPU sorted
Hi all,On my router it seems not send "direction" mark to collector
hello everyone i try to make ssh connection between vlan10 and switch4 in lan2 and i dont manage to do this vlan 10 ip: 192.168.10.0/24 private ->> 172.31.0.0/16 "dmz" ->> 209.165.200.0/6 publiclan2 ip:172.19.0.0/16 private ->> 209.165.200.0/24 publ...
I tried create ipsec tunnel using cryto maps. I tried using both transport mode and tunnel mode and both works but I am confused about working of tunnel mode. I know tunnel mode encapsulates whole packet and adds new IP headers to packet but I am c...
My problem is as the title says. I already configured the WLC from the website. Attached below is the pkt file configuration and if you want to access the WLC site (user:Admin1,pw:Admin123)
