how to get bandwidth Monitoring access from asa Firewall 5512.Kindly help me with that concept.
I can check the top 10 users who are using bandwidth but not managed
I'm running ios ips on a c3825 isr. We were having multiple instances of intermittent latency and poor wan performance. I disabled and retired all signatures from basic category except a handful. I noticed there was still poor performance. I then...
Hi
I am trying to create a simple access-list rule that restrict an external subnet to ping to any host behind the firewall.
The rule is access-list outside-access_in permit icmp host 172.2.1.2 any
The rule loads without no issues. But, the external ...
I have updated ASA ver 9.1 from 8.2. After copying the config in asdm I found out that all the NAT statements was missing hence tried to configure NAT. But struggled due to new format of commands. After configuring the NAT I tried to establish Site t...
Hello,
I am trying to build a custom report to view the number of users in a specific subnet (example, 192.168.10.0/24) who were online in the last 24 hours. I do not know if it is also possible to see how many users in this subnet were online simul...
Dears,
we have purchased ASA 5525X with firepower, i m running 8.2 on my old asa i want to migrate the configuration, i am using the below link tool for the migration but it is not doing properly,
https://software.cisco.com/download/release.html?mdfi...
Dears
when I migrated to 9.5 all my access-list are showing me like host :: , but in startup config I can see the IP address.any ideas please.
access-list DMZ extended permit tcp host :: host :: eq www.
Thanks
Hi Guys,
Good Day!
I would like to ask what is the difference between the 2 static NATs configuration below,
1) nat (dmz,outside) source static obj-private-ip obj-public-ip destination static obj-any obj-any
2) nat (dmz,outside) source static obj-pri...
I have setup ASA 5525 firewall with inside, outside and DMZ.
From inside PC, I can ping the inside interface of the firewall, from DMZ system I can ping the DMZ interface of the firewall.
But from inside PC, I can not ping the DMZ interface, also fro...
hi,
I'm configuring an asa 5515-x with firepower services now I wanted to add it to manager unfortunately I have updated the sfr module to 6.0.1 but I have installed management center version 6.0.0 vm. now I have to upgrade it to 6.0.1 but I can not ...
hi,
I am configuring an asa 5515-x firepower services and I came into this problem that acl configured for service policies does not match any traffic. Actually when I want to select a specific traffic flow to inspect using sfr module or perform band...
Hi community ,
there is no data on firesight . How can i solve this ?
on ASA :
show service-policy sfr
Global policy: Service-policy: global_policy Class-map: sfr SFR: card status Up, mode fail-open packet input 25687, packet output 25687, drop...
Hi, we bought a 5512-X with TAMC licenses for one year (september 2015 to september 2016).
We received the ASA on march 2016, that mont i installed the ASA and generate the licenses but when i put them on Firesight i´m seen that the expiration date i...
I'm hoping someone can assist me. I purchased a used ASA 5510 last year with an advanced security license on it. Recently I had a corrupt flash and had to format things. Unfortunately the advanced license key was lost with the format and the base ...
Hi Guys
Has anyone experienced any performance impact by redirecting traffic to SFR module ver 6.0?
I have two ASA5525-X running SFR version 6.0.0 connected to DC firesight ver 6.0, there is a 100Mb internet circuit on the firewall and not more tha...
