We have a route-based VPN configured to a vendor, and I attempted to apply an access list to the tunnel interface. All traffic was blocked. I've not been able to find documentation on how to apply and ACL for this type of VPN, but this isn't working...
Forum Posts
My ASA license is smart registered, but there is no internet for the device (net can't be provided). What happens when the Communication Deadline exceeds.The current license in ASA is Base.
Why would an arp reply be sent as a broadcast? And out on an interfaces that didn't send the request?I've disabled proxy arp and I can still see arp replies from our cisco12:05:18.299985 5c:71:0d:xx:xx:xx > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), ...
Whenever a change is deployed, the following warning is displayed: Access Policy: Logging: FTD-XXXXXWarning: Access Control Policy Logging configuration is invalid. Access Control rules have syslog configured to use Access Control policy's logging co...
Resolved! Major Bug in FTD 7.2.4
Hi Members, We have cisco FTD 1120 firewall and the firmware is 7.2.4 installed and in this month my firewall has 3 times crashed and impacted my business and because of these crashed I lost almost 15-18 lacsFurther I checked with cisco tec team and...
Hi Cisco community, As we configured VPN manually from ASA to FDM, we notice there is some function from ASA that the local vpn user can assigned dedicated IP as per below. I find it at FDM local user setting only can put username and password. Is it...
We have been having issues with our CSM 4.24 deployments to a specific 55xx ASA context, where all recent policy deployments are failing with the error "Unable to Communicate with Device" / "No response to connection attempts to this device". Another...
I want to do the same things as described here: Solved: Cisco ASA and Internal Hosted Website - Cisco Community But the only different is that that the users are one VLAN1 and the webserver is on VLAN2? Thanks Frederik
I am trying to access FTD 2110 using HTTPS, and I am getting "Application Failure" error. It says FDM application cannot be opened. Please try again. I tried "configure manager delete" and then "configure manager local" but that did not help.Can some...
Currently I have a Firepower 1010 managed by FMC.I want to have 2 x VLANS, a management VLAN (100) and then a LAN VLAN (with DHCP) (200).From then I want to have 2 port channels (EtherChannels) with 2 Ethernet Ports each which will then go to 2 x swi...
I noticed the time on my two FTD 1140s was set to UTC. My FMCv is set to sync with an NTP server and is working correctly to EST. Shouldnt this setting be controlled by my FMCv and be passed on to my FTDs? If this is not the case how would I set the ...
Hello We require an expert's assistance for the migration of FortiGate to Firepower Threat Defense (FTD) as part of our technological refresh initiative within End user request. Currently, there is no provision for the acquisition of a Firepower Mana...
Hello, everyone,I wanted to share a problem I am experiencing regarding SSO configuration (the SSO server is a FortiAuthenticator) for Cisco Secure Network Analytics:As per the guideline, I entered the rootCA in the cisco SNA Trust Store and after va...
We have an issue with our FTD 2110 device complaining about disk usage issues. The device is at 71% capacity and the Readiness check fails it because there's not enough space being detected. I went through solo to find old update files etc... and rem...
We are trying to remediate the RA VPN vulnerability of CVE-2023-20269. We use TACACS+ to login, but there is a local backup account in case TACACS+ goes down. Is there some way to prevent this account from being utilized by AnyConnect?I understand we...
