I'm looking to get some basic reporting from FMC for things like top talkers but can't seem to do it in FMC because a lot of the logs are not going to the event viewer due to its limited size. What is a simple tool that can be integrated to get repo...
Forum Posts
Hi all,As the title says, I'm trying to upload an upgrade file (Cisco_FTD_SSP_FP1K_Upgrade-7.6.0-113.sh.REL.tar) for my FTD to FMC. For some reason when I select the file and click upload the browser behaves as expected. However, after a minute the u...
Good day everyone.Yesterday, I was working on a Cisco ASA 5512-X Firewall that was being used as a VPN Firewall when suddenly I was disconnected from the ASDM. My SSH session from Putty was closed, and I am unable to get back into any of them. I took...
Resolved! Integrate FMC HA with ISE pxGrid
Hi, I have one pair of FMC and on pair of FTD, currently FMC appliances in HA setup and we have successfully integrated with ISE pxGrid. The question now is what will happen if the primary FMC fails, will FTD HA still receive the IP-to-SGT mapping fr...
Hello, When I login to the FTD CLI, and check the management IP is shown as 203.0.113.130. My FTD version is 7.4.2. I checked in another FTD in version 7.2, but it is showing as "Unassigned". Please advise. Thanks Shabeeb
Planning to upgrade/replace ASA5525X with Firepower1120 Series loaded with ASA image. Need proper guidance on1. How to perform this move.2. Things to keep in mind.3. Can I simply load existing config on FPR1120 and turn it on. Will everything work ju...
Resolved! device-tracking mode guard vs legacy DAI
reading Feature history of SISF Security Configuration Guide, Cisco IOS XE Dublin 17.12.x (Catalyst 9400 Switches) - Configuring Switch Integrated Security Features [Support] - Cisco i have a feeling that device-tracking mode guard is an alternative ...
Resolved! Upgrade ASA 5545 with Firepower module
Hi,I would like to upgrade my ASA 5545 with Firepower module from version 9.12.4 to 9.14.4.The Firepower module is running version 6.4.0.14 and is managed by FMC, which runs version 7.0.2 (build 88). My question is:Is ASA firmware version 9.14.4 comp...
Hello everyone, I'm trying to use the Firewall Migration Tool (FMT v7.0.1) to migrate the config of ASA 9.12 to FMC 7.4.2. After successfully uploaded the the text file of ASA running config into FMT, and then started the conversion after selected th...
Hi all, Is anyone here also experience this kind of issue on the FTD? we notice that some return traffic being blocked on the FTD. Thanks for the answer!!
Resolved! Cisco FMC 1000 smart licensing error
Hi, Tried to register the FMC1000 device for smart licensing and got this error msg"Failed to send the message to the server. Please verify the DNS Server/HTTP Proxy settings."The DNS server IPs is configured and Proxy is not enabled. Tried the cur...
Hi Team, We have old Cisco ASA need to confirm that config and sessions are synced to the Passive ASA????? This host: Secondary - ActiveActive time: 30555250 (sec)slot 0: ASA5515 hw/sw rev (1.0/8.6(1)2) status (Up Sys)Interface INSIDE (10.30.136.10):...
Currently on a Cisco ASA, we use RADIUS authentication for WEBVPN users. For the logs on the RADIUS server we are not receiving the originating public IP of the users failed/successful attempts, rather we are getting OUR public IP of the gateway for ...
Hello, We have a customer who is running their perimeter firewalls in Active Passive failover. The firewalls in single context mode. I have the below queries regarding the Mac address that will be used by the primary unit. 1. What will be the MAC a...
On my FMC, I recently noticed an issue when I try to access the module exclusion web page under System > Health > Exclude. When I click on the menu, I get the following error:Error while fetching dataDetails{"errors":[{"instancePath":"/2/excludedMod...
