Hi all,We’re planning to upgrade our FTD 2100 series and FMC version to 6.6.4. Current version for both FTD and FMC were 6.6.1 and FTDs are in HA deployment.I’m planning to upgrade our FTDs from FMC by installing the update patch.But when we visit th...
Forum Posts
Hi I have a 1010 Firepower on the edge with 2 S2S VPN connections established on it.Now when I try to connect from a client inside of the 1010 to a VPN Gateway on the internet, it is not going through, any hints on where to troubleshoot? as these dev...
Hi everyone, I'm managing my FTD via FMC.I'm sending my syslog to an external server.Now, I've noticed that sometimes I get two of the same log under different user, for example: Jun 3 10:54:59 172.20.1.95 :Jun 03 07:55:00 UTC: %FTD-config-6-111008:...
I just saw today that FTD finally supports VTI for a few months now. I was sad to see it's only new the latest version which ASA 55xx-X do not support. What are we to do if we need VTI supprot on ASA 5506-X? Is that ever coming?
Hi Cisco Community , I tried integrating FMC with AD server and able to integrate Ad with FMC .when i try to download users i get error invalid realm id . iam using FMC version 6.6.4 and windows server 2012 R2 . Attached error image . Thanks for a...
Warning: this is a salty message. You have been warned.While FMC 7.0.0 had a lot of nice and needed features, it went backwards in many others - including basic system functionality. Today’s case in point, the FMC internal email notification system (...
Hi,My customer recently decided to switch from Cisco to Palo Alto as perimeter firewall solution. The design decision was to keep the same security policies and this implies PA provider needs the backup of existing ACPs in our Firepower solution.In o...
Where do I find a procedure where I can configure firewalls on active/standby and DRFirepower 4410
Hello,I was able to read the below thread and it was very helpful, but it still didn't answer one question for me. The setup is pretty standard I think. We have an ASA running FirePower Services. We have a DMZ with public facing services. So on the A...
Dear All,I have upgraded my ASA 5525 with Firepower Services and FMC from 6.4.0 to 6.6.1. After upgrade, there is issue that after deployment succeded error message appear said "Process Status - adi exited 1 time(s)" and there is access policy config...
Hi Everyone,I have been stuck for a while trying to get this to work, I have Cisco CML 2.2.1 where i managed to get Cisco FMCv 6.4 up and running and managing two FTDv 6.4 however, the option for add a etherchannel doesn't appear. I have read somewhe...
Hi All When I try to access FDM on Chrome, this what I get, it used to work previously but slow.On Edge the page does not even open, it keeps loading.. using Windows client, what are other browsers I can use also to be able to administer the applianc...
Hi,Just after some info which I cannot find definitively anywhere on Cisco.comWe have an ASA 5525 with a 200 VLAN licensed limit. Would anyone know if this VLAN limit applies only to sub interfaces (i.e. max of 200 sub-interfaces) OR if this would a...
Hello @Rob Ingram @balaji.bandi @Marvin Rhoads @Richard Burts @Marius Gunnerud I am using MerakiMx84 Firewall provisioned with 2 WANs, 1st WAN is primary and 2nd WAN is on ready state as Backup. With Help of Preference Internet routes, I setup s...
I recently setup a VPN to a remote site and that remote site has multiple subnets. The VPN is up and running and subnets can access main site and its resources fine through VPN except internet. Meaning I am unable to access the internet from any of t...
