Hi,
I am planning to use 3 of the QSFP28 ports of the Cisco Nexus 93108TC-FX3 as breakout interfaces for 12 servers with SFP+ interfaces, and the other 3 QSFP ports as VPC or uplink.
Is this possible?
Hi everbody,i try poap usb with a N9k 10.3.5m NXOS. With paop script from git.nexus9000/nx-os/poap/poap.py at master · datacenter/nexus9000 (github.com)After some troubleshooting i have changed poap sriptline 1075 copy_src=os.path.join("/usbslot%s" %...
hi i have Downloaded Rpms and copy to an nxos device in bootflash.now i want install the rpm in a Guestshell with Sudo yum install /bootflash/nameofrpm.rpmguesthell will access a mirror, Problem i have no direct Internet Access is it possible to inst...
Good evening, teamAny suggestion how I can recover console password of a nexus 3000?I have tried the below but it is not working:switch(boot)# config tswitch(boot)# admin-password new-passwordswitch(boot)# exitswitch(boot)# load n3000-uk9-kickstart.6...
Hello, I reserved the NDFC sandbox and connected using the standard VPN connection. I'm unable to access the NDFC GUI with the given IP address. I RDP into the devbox and tried to connect to the Nexus Dashboard and was unsuccessful. I'm able to ping ...
Hi Team,
In the n9k yaml file, I have devices section like this:
devices: device_1:
device_2:
In the script, I call this object as :
self.parameters['uut'] = self.parameters['testbed'].devices['device_1']
I need to hardcode the hostname ...
Hi Cisco Family,I'm experiencing an issue where I've just purchased a new Cisco Nexus 3064-X on which the n3000-uk9.5.0.3.U5.1f.bin image is installed. We've to enable features for each configurational protocol such as " Feature BGP or Feature OSPF" ...
Hello Everyone! I'm trying to create/write a file in bootflash: through a script and It fails... I tried to run the command directly in the TCLSH interpreter but I get this message: N7K-CORE# tclsh
N7K-CORE-tcl# open bootflash:///clock.log "a+"
could...
Hello,
I need to enabled jumbo frame on the port-channels on Nexus 7706. These Nexus 7Ks also have OTV which is use to stretch VLANs between Data Centres.
On all the port-channels, the MTU is : 1500 as below:
interface port-channel101description ### ...
HiI read on the cisco website that for some Nexus 9000 Switches we have a concept of Port Groups. That means for example in a group of four interfaces, if we configure one port in 40GE mode then we cannot configure the other three ports with another ...
Hi,I have some questions about installing new line cards in Cisco Nexus switches. The switches are working in VPC mode.1. ¿Is it possible to install the line cards while the devices are working? or is it necessary turn off each switch?2.Considering t...
`Hello All,I've recently been introduced to a setup with a Nexus 7004 chassis running as interconnect to the orgs's servers. The Nexus device then connects back to the core. There are multiple SVI's setup on a primary VDC. These have historically bee...
The problem: We have 2 Data Centers about 40 miles apart each with there own connection to the internet.. and also 2 wires between the N7Ks at each site for data center to data center. Each data center has 6 switches... two 7ks, 2 5ks, 2, 2ks.Alth...
When will the NDO Data Model be updated for the separate L3 Out and Tenant Polices Templates?
We are running version 4.2.1d and utilising terraform/yaml files to create new transit L3Out and would like to fully automate the process but current NDO M...
