Hi All!I have a quick question! I have two 7960 phones configured working with a CallManager. Can I add two more ip phones but use them as SIP. Please let me know!Thanks,Paul
I'm having some trouble with this network module being recognized by my router. At one time, the router recognized the module and the daughter cards (4-FXS/DID and 4-FXO), I had it registered with call manager, but could not produce dial tone on the ...
Folks, We have 2 buildinging connected via Fiber connection. We are planning to deplay callmanager (pub and sub) at both sites for redundancy purposes. My questions is as follows:1) If the connection between the 2 building goes down, some phone...
Hi,I need to beak out fax calls which are received through an MGCP gateway (e1) to a router which is running the IOS fax onramp TCL script.I was going to configure a route pattern in CCM for my 2 fax numbers & point these to the TCL router.Then my ca...
Hi!I´m working with Callmanager 4.1(3), a Switch, and one Server (with IIS) for ASP apps (with SDK)..I can run all samples, and i made a few.Well, i have 3 7960 phones, and one 7912.. and i need to identify the model, because the 7912 dosn´t support ...
Hi,in the installation description of the OS 2000.4.1 is a description "how i enable SATA RAID an disable Hyperthreading on MCS-7825-I1 and IBM x306 Servers".Must i do the same Procedure on MCS-7825-H1 also ?RegardsArmin Kleemann
Quick background for you all.Unity 3.1.6 servicing 7 CCM Clusters all working fine (CCM3.22cspH up to 3.3.5).Adding another 3.3.5 site, users are able to dial Unity on the Pilot number, customise mailbox greetings. Things go wrong when a phone is co...
hi,I've got a problem language settings using a CME 3.3 system with phone types 7912,7920,7940,7960.I configured locale settings to german and 7912 as well as 7920 phones show the correct softkeys and menu entries, but on the 7940/60 phones the softk...
Hi,When I press "9" to access outside line, right before I hear the outside dial-tone (all relevant route-patterns are configured to provide outside dial-tone) I hear three very quick beeping sounds and then comes a dial-tone.I have quite a few route...
I have a 2811 with Version 12.3(14)T2. there is an ISDN 30 (e1) plugged into this router and frequently all 30 channels are displaying this error message*Jan 5 14:50:37.251: ISDN Se0/0/0:15 Q931: TX -> RESTART pd = 8 callref = 0x0000 Channel...
Dear all,I have seen the use of Outlook Plug-in for Web Dialer in a demonstration. This allows pressing an icon in Outlook and dialing the phone number of contacts stored in outlook address book.Where can I get such plug-in?Many thanks!xwang
Does anyone know if it is possible to implement the loud ringtones for the 7920 with CallManager express? I can't get the tones to show up under the download ringtones section.
HiI've installed the IPPhoneForward app from myvoipsource.org on my CM. It doesn't work, so I've been testing my AXL...I believe I should be able to browse to:http://10.52.234.240/CCMApi/AXL/V1/soapisapi.dllThen enter the Windows administrator/passwo...
HiI've installed the IPPhoneForward app from myvoipsource.org on my CM. It doesn't work, so I've been testing my AXL...I believe I should be able to browse to:http://10.52.234.240/CCMApi/AXL/V1/soapisapi.dllThen enter the Windows administrator/passwo...
Hi,I just connected a 2800 series with IOS 12.3T11 to an Avaya PBX using BRI.I noticed that the Avaya sends caller NAME information. Not only the calling number but also the calling name. Cisco Phones display both, calling name and number when a call...
