Dear Teamits my configurationTask:enable ospf feature and configure leaf1-9k(config)# feature ospf leaf1-9k(config)# router ospf 1leaf1-9k(config-router)# exitleaf1-9k(config)# int e1/2leaf1-9k(config-if)# ip router ospf 1 area 0leaf1-9k(config-if)# ...
Forum Posts
Good morning all, I want to configure vpc in Cisco Nexus 5596up switch with configuration synchronisation. I want to use these switches in my network as core L3 & below connected devices are all L2 catalyst switches. How can I do this ? Kindly help m...
Hi all ,I want to log any command (show version , exit ..etc) when any user login the nexus n7k , n5k .I set up the config on N7K but I can't find all the commands on aaa accounting report of ACS 5.6 .There are no " aaa accounting commands 0/1/15 " o...
Hello,I am looking(with no succes until now) for EU Declaration of Conformity for Calalyst 3850 & 2960 & 2911. Perhaps someone could support here
Hello, Experts.We are attempting to reach the console of a UCS C220 M5SX that operates a Nvidia T4 PCIe 16GB 70W GPU. The vKVM console window opens as expected, but the display is blank. What configuration/settings/drivers/etc. should be in place in ...
Looking for the datasheet and step file (3D drawing) of this part : STK-RACK-DINRAILI need to provide the datasheet to my client and need the 3D drawing to design the server cabinet.
Hi guys, Need some help now. We have one fortigate HA clutser connected with two Nexus 9504 (Topology in attachment), Each fortigate has two Agg-link. We tried to test some traffics like Telnet and FTP session during Failover, the session has to be ...
This session introduces the use of a VXLAN EVPN gateway functionality in an ACI fabric to establish native Layer 2 and Layer 3 connectivity between two different types of VXLAN fabrics (in this session- NDFC VXLAN and ACI iVXLAN). The session covers ...
We want to put you in the driver's seat of your network! Learning about data center networking should be simple, accessible and manageable. With resources like webinars and expert insights, we're here to help you take control and unlock your network'...
Hello,I have a message like this:Admin-CORE1_VDC# clock set 15:26:00 7 december 2014Setting clock from CLI is not allowed in this VDC.Use the following config command to use the "clock set" command.clock protocol none vdc <vdc_id> If I issue that com...
Dears,In the following points :-1 - A VRF "CUSTOMER1" assigned to multiple L2VNIs from (10001-1000N).2 - The L2VNI are mapped to the same VRF "CUSTOMER1"3 - Then VRF "CUSTOMER1" would be mapped to a single L3VNI, let say 30000.For L3VNI I have local ...
Hi All I ran into an anomaly prepping NXOS based hardware for an upgrade. The build consists of 4 vPC pairs. Two Nexus 9336C-FX2's, two Nexus 9364C-GX's, and four Nexus 93180YC-FX3's. As far as the vPC configuration is concerned, I have the same con...
Hi all, we are facing same issue (described in CSCvk25616) with ESXi 7.0.3 and HyperFlex 5.0.2.g. In our setup we have 2x datastores and after reboot only one is visible where we have ESXi system logs. The datastore which is missing after reboot hold...
We have three new exciting webinars this Qtr. You can access the individual registrations by clicking on each session link. Otherwise, you can register to multiple sessions here: https://cisco.webex.com/webappng/sites/cisco/webinar/webinarSeries/re...
Looking for help for the POAP - Multi_Step installation we are in the process of using poap.py script for nexus TOR to build the configuration and also do the code upgrade Single step upgrade works fine from 9.3.9 to 9.3.13 however we want to do mult...
