Is it possible to run two routers with HSRP and at the same time use the "ip load-sharing per-packet" command in the FE interface?
When I right click on a 3524 switch port in ciscoview I only get 'monitor' and 'clear all addresses' options. How can I configure the switch port? I already upgrade to the latest ios and installed the latest device patch on ciscoview.
I am preparing a 7204 router for a test and when I log into it the promtp says:Router(boot)>Then when I go into enable mode it's:Router(boot)#I have a 7204VXR with a NPE-300, a FastEthernet I/O controller, and a Multi-Channel DS3 port adapter.
Does anyone know if there is a release out there that supports setting the BW statement on your router asymetrically?With all the asymetric DSL out there, I'm looking for a way to trigger alerting when I peg my upload without generating alerts on my ...
Hi,cisco 3660 + NM-2CE1B + CAB-E1-PRImy configuration :router(config)#contro e1 3/0router(config-controller)#channel-group 0 timeslots 1-31router(config-controller)#no shutrouter(config)#int s3/0:0router(config-if)#ip add 10.201.2.1 255.255.255.252ro...
Our customer's CISCO2621XM is not recognizing their WIC-1DSU-T1 but it will recognize a WIC-1T. The WIC-1DSU-T1 is recognized in the older Non-XM CISCO2621 Router. Any thoughts? Do we need to replace the router or the WIC-1DSU-T1- or is there anoth...
How can I clear all the counters and logging info on the router without reloading it?Thx,C.
HiIs it possible to run GLBP in a Cat6500 with 2 Sup720 and SSO (running native mode ofcourse) as far as I can see this can not be done (yet).Best RegardsAnders NilssonUmeå Univ
Help needed pls ,got Cisco 3660 router on my lan handling Vlan routing ,that connects into Catalyst 5509 ,i installed new Cisco 2620 ,i created new vlan for segment on 3660 router and added port on 5509 where new 2620 plugs into to new vlan group. I ...
Hi,Have an IGX 8410 running SWSW 9.1.16, with only 1 NPM. Have a spare NPM in stores, but it has SWSW 9.2.X on it.Would the 9.2.x NPM work in the 9.1.16 IGX or would I have to down-grade thw SWSW on the 9.2.x to 9.1.16 ?Many Thanks in advance.
Hello All,Is it a good practice to have a multiple VTP domains in same Physical Network with same IP schema . We are going to upgrade our Automation NW with 2 Nos of 6509 and 5 Nos of 4507 with L3 capability . The Solution provider is proposing that...
We've changed two ports on a c2950 from autoneg to 100 fd. We have also changed the portsettings on the servers hanging on these two ports to 100 fd. The ftp-speed between these two servers are really slow after these change. We are using sw 12.1(13)...
Hi,I have 1 Catalyst 2950. All ports are busy.on 2 of them I have 2 Unix servers with Ethernet boards configured as 100Mb/FD.Everybody can ping everybody with a nice throughpout (20-40 Mb/s) except those 2 Unix servers that cannot ftp anything above ...
Is there a way to delete devices from Cisco Works (RME) by command line?Tommy
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |