IS there a way to aggregate 2 T3 lines? like PPP multilink for T1's, does anyone has any ideas, thanks for your suggestions!
IS there a way to aggregate 2 T3 lines? like PPP multilink for T1's, does anyone has any ideas, thanks for your suggestions!
I have a router cisco with 2 fastethernet interface,the first interface have a ip address with ospf routing enable.Now the second interface is shutdown state.If first fastethernet interface goes down (because is broken or the switch doesn't work),can...
Hi I trying to configure NAT on a 1711 Security router. My outside interface is fastethernet0 address 68.238.170.27, and my inside interface is VLAN1 address 10.10.10.1. I am able to ping a public addres from the router, but I cannot access the inter...
What's maximum number of neighbor that bgp can peer with?
Hey I need to Document my network which includes around 10-13 cisco switches and routers. Now I dont know where to start. Should I manually document everything or use some kind of a software that automates the documentation process.Please reply back ...
I've had 2 occasions now where a PC plugged into the network has a DHCP server service running. This of course, will eventually bring the network down.How can this be prevented?Thanks
I was wondering if any one kowns the command to turn off the web configuration interface on Cisco Catalyst switches. I have several 2924 XL's, and there's a security issue with the web interface.
Hi,I am trying to configure a 3740 router. The access over PSTN is workign fine. But over BRI it does not seems to be workingWhen I debug the ISDN q921 and q931 I get the following* Calling Party Number i = x0083, '01313485000' ...
I am trying to monitor Cisco router perfomance ( specially cpu % and memory utilization ) using standard snmp monitoring tool.How can I get the Cisco's private OID descriptions ?
I have a 2950 LRE and want to put each port in its own vlan for a little security between the ports but allow internet access to all ports through one of the fast-ethernet ports that connects to an edge router. Is it possible to have the FA port a me...
The below design started as a star but SW3 was added to SW2 because Switch 1 only had 2 fiber ports.I need to add another switch and my optionsare: I either add another switch on top of SW1 with fiber ports, of which none of the copper ports are used...
Tested on 7513 PA-T3 to connect to remote site via 7200 PA-T3 no issue. Line is up. Tested on 7513 PA-T3 to connect to remote site via 3660 using NM-1T3/E3. AL Alarm. Line is down. Below is my sample config 3660card type t3 1!controller T3 1/0!inter...
Hello,I've a problem with a serial connection. I've a 2500 router connected with a Catalyst 6509 through a 2 Mbps serial line.The download transfers to the router side are perfect, with rate up to 250 KBps. But on the other direction (uploading) they...
Hello,When i am trying to follow the procedure of 'recovering password' on Router 3660, during booting, it displays message that "PASSWORD RECOVERY FUNCTIONALITY IS DISABLED". I guess this is due to the wrong registry setup. Becasue of this, I am not...
When I use the following configuration all of the static routes are blocked, not just the 4 in the access list. MSFC c6msfc2-jsv-mz.121-13.E6.binrouter ospf 1redistribute static metric 10 metric-type 1 subnets route-map Block-Evolve-Outaccess-list 10...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-30-2025 12:23 PM | ||
06-17-2025 01:54 PM | ||
06-14-2025 12:34 PM | ||
01-22-2025 07:00 AM | ||
12-30-2024 06:12 PM |