What happens when an IMA trunk fails ? Say I have 2 or 3 T1s in an IMA group and one fails. I assume the cells will start processing over the remaining trunk(s) (or T1[s]). I couldn't find any references to this.
What happens when an IMA trunk fails ? Say I have 2 or 3 T1s in an IMA group and one fails. I assume the cells will start processing over the remaining trunk(s) (or T1[s]). I couldn't find any references to this.
Hi everyone,I have a Cat4k CatOS 7.1(1) as VMPS-Client.Sometimes I receive a syslog " %SYS-4-P2_WARN: 1/Host 00:30:05:5b:0e:31 access denied on port X/XX "and the host can't work properly. The MAC isn't learnt and no traffic aren't received on the po...
Is it possible to configure Policy Based Routing on the ethernet link where in i want some traffic originating from specified source on one ehternet link and some on other ethernet link and if one of the ethernet link goes down all the traffic shoul...
I don't trust the telco and am having the same exact problem with two sites. Both sites have 1721s with WIC-2A/S's. 1,000 1,000 byte PINGs has about 96% successful. Config:interface Serial0 description test circuit bandwidth 64 no ip address encap...
What is the distance limitation on a 6500 switch fibre module using multimode fibre not singlemode?
Hi; I appear to be having strange trouble with CEF and adjacency on a Cisco 1711 running 12.3(7)T. I suspect that it is a bug.I have now recreated the problem in a lab environment. A small diagram is attached. The network is setup as follows:- Cisco ...
I'm looking for a guideline as to how much bandwidth I need per user for an internet connection. Traffic will be limited to HTTP/HTTPS and e-mail.I've read that rule of thumb for ISPs is to take in no more than 5 T1's per every T1 connecting to the ...
PIX525 configure PPTP to allow remote user dial at VPN.PIX configure :vpngroup vpn3000 address-pool vpnpoolvpngroup vpn3000 dns-server 192.168.0.20vpngroup vpn3000 wins-server 192.168.0.20vpngroup vpn3000 default-domain vvgroup.comvpngroup vpn3000 id...
I have numerous network issues that started between 2 of my campus sites across a T1 between 2501's. They can't save file to the network, can't get to outlook, illegal operation and numerous others. When I look at "debug ip packet detail" on the lo...
Hello,We have a 2511 router set up so users can dial in and access our network. The user dials in fine and gets an IP address but the subnet mask is 255.255.255.255 and I need it to be 255.255.254.0 How do I change this??Also the Gateway gets set the...
I think I'm running into the following problem http://www.cisco.com/en/US/customer/products/sw/cscowork/ps2073/products_tech_note09186a008019ce49.shtmlHas this been fixed in IDU7.0 ?Please advice.
We are in the process of switching from multiple T1 circuits to a single channelized ds3. Currently all our T1s are plugged into one Cisco 3661 router using multple t1 serial interfaces and external t1 csu/dsus. Our telco made a point of stating tha...
I have router A with 2 serial frame relays, dlci 101 and 102. I have remote router B with 1 serial frame relay dlci 150. I was planning on moving router B from frame leg #2 dlci 102 to frame leg #1 on dlci 101. Everything is already configured on tel...
If I wanted to do a manual IOS upgrade to a router or switch where would I find the /tftp directory on CW2000. On my LINUX box I have TFTP setup to use /tftp subdirectory.What is the path to get to a source file in the example below if I want to get ...
Erase startup??? - alternative commandDoes anyone know an alternative command to use instead of "erase start".ThanksEK
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |