Dear MembersI want a switch with the following features and requirments, can someone help me out.GigaBit Ethernet Ports = 410/100 Ports = 12MM Fiber GBIC Modules = 2 Waiting for a solutionregards
Dear MembersI want a switch with the following features and requirments, can someone help me out.GigaBit Ethernet Ports = 410/100 Ports = 12MM Fiber GBIC Modules = 2 Waiting for a solutionregards
First of all thanking all of u that spent time in going thru my issues. Here is the story:I knew that one of my CAT-6506 ( Cat OS 6.3(5) ) here is been converted out from Native to Hybrid Long back. When I enter dir bootflash from Sup Mode, it show...
HiI have a serious problem with AS5300 I can't access it by telnet and forgot the password of auxiliary access and when I try to access it with console I always pass the hardware check test but when I press the break button I get nothing and at the e...
Hi,I have two sites both with cisco 2600 series routers with channelized E1 cards, both sites have Primary Rate ISDN with 8 channels activated. The idea is to provide all 8 channels bonded together to provide 512k backup link to our 2Mb serial VPN c...
Can you put an etherchannel group in a specific VLAN on a native mode 650x?Also, if you want to route between VLANs on a 650x running native mode IOS, do you just create VLAN interfaces?Thanks
HiI have problem with ressetin sessins on catalyst 6509 runing IOS Version 12.1(13).I want to monitor and reset session on port 3/2.This is my configuration.monitor session 1 source interface Fa3/2monitor session 1 destination interface Fa3/47-------...
Hi.I'm installing a WIC-1ENET on a 1750 router that seems to follow all the Cisco guidelines and still get the following:"00:00:08: %PQUICC-1-UNKNOWN_WIC: PQUICC(0), WIC card has an unknown ID of 0x39"The card is installed on port 1 which is OK with ...
I was just wondering what the difference is between using:1. interface Multilink xand2. Multilink virtual template xinteface virtual-template xcommands to create a MLP. Currently, we have 2xT1 from one router to another router. I want to be able to c...
Hello All & Greetings.I have 3 2500 series routers properly connected and have configured the serial int with proper IP addresses. I can ping from any int on one router to any int on any other router. And, thisis true of any of the 3 routers that I h...
Hello, we currently are doing nat on a 2500 router , inside ethernet and outside on serial. This is over a WAN link to another company, the reason for nating. We are planning on having a VPN device(501 or 3002) as a backup to the serial WAN port on ...
-Process= "IP Input", ipl= 0, pid= 31-Traceback= 603FBF58 603FE53C 603F7BF0 60999680 6099CF60 60992BF4 604B719C 604B5ED0 604B60A0 604B627801:29:25: %SYS-2-MALLOCFAIL: Memory allocation of 32768 bytes failed from 0x603F7BE8, alignment 0Pool: Processor...
What service is port 2228 ?
Hope you could help me,I have a situation as follows:3640 to WWW,fa0/0 conneted to 4506(L3).3550 EMI have a les connetions to HQ.4506(l3)main Hub site have a unix server LOCAL USERS CAN ACCES,these are connected via g0/1 g0/2 to 3550On main sites u...
HI Buddy, Can anybody tell me how to upgrade CAT IOS to Nativ IOS. is thereany procedure. pls suggest me or tell me the any cisco link where i can find.Thanks & Regards,Ciscobuddy
I cleared the config on the Router using the Erase Command. Does that also erase the config of the WIC 1DSU T1 card?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |