I was configuring this 4506 switch for exception dump so that it'd send the dump file to an ftp server on our network.c4506(config)#exception dump x.x.x.x%coredump feature is not supportedWhy did I get this error?? It worked fine on our 3560 switch.
I was configuring this 4506 switch for exception dump so that it'd send the dump file to an ftp server on our network.c4506(config)#exception dump x.x.x.x%coredump feature is not supportedWhy did I get this error?? It worked fine on our 3560 switch.
Hi ,I have 3 switches connected as followingSW1--L2------->SW2-----L3------->SW3 SW3 has the SVI for VLAN 10 , can I add users to VLAN 10 in SW1 . ( VLAN 10 is created in all VLANs). The connectivty between SW2 and SW3 is layer 3.Regards
Se tiene un switch 2950 directamente conectado a dos switch 4507 en la misma vlan con HSRP. La configuracion en el puerto de los switch 4507 como deberia de estar, como trunk o como acceso ?4507----2950----4507
Somebody told me that a Router should not a act as DR/BDR for more than 1 LAN segment. In my specific installation I have a 4506 with SUP IV that acts as DR for 5 Segments. Are you aware of such limiation or do you have some link that refers to this...
Can tacacs be configured for first level access also and not just the enable mode ? Haven't been able to find an answer ,though just by looking at the config options it just looks like you can just do the enable mode .
Hi All,why am I getting the below, a null entry for 192.168.169.0.?Roger#sh ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA ext...
I have a 6509 with redundant sup2/msfc2's in native mode, is the boot image on the MSFC necessary?
Dear all,Kinds help me to solve out the problem with ios upgrading.I have a 2621xm router I am upgrading 12.3 IP Plus IOS and I have deleted old Ios but after deleting the old ios I am not able to upgrade the ios its giving some error and even if I ...
I am in the process of moving connections off of a Cat 4006 onto a stack of 3750s. On the 4006, I see no errors on the show interface command. I move the cable ( same exact cable ) from the 4006 to the 3750 and the port gets CRC and input errors.The ...
I had a need to replace a 2950, so I copied the startup config of the old switch to a file, which I then copied onto the new 2950. The switch passes traffic, and when I console into it all the parameters are correct, but I can't telnet to or ping it....
Ive pasted my vlan and acl config.... here's what strange, from vlan 2 i can ping vlan 1 int.. shouldnt the ACLs prevent this:interface Vlan1 ip address 10.0.0.171 255.0.0.0!interface Vlan2 description DMZ_192.168.1.0 ip address 192.168.1.5 255.255.2...
Friends,Can someone plz help me with this. I want to 7206 router as vtp server domain & Vlan database but I cant configure can someone plz help me? R5-7206(config)#vlan database ^% Invalid input detected at '^' marker.R5-7206(conf...
Hi,I need advice urgently.I have 3 routers.When I configure primary and secondary ip addresses on a single physical interface,I do not want to use sub-interfaces because I will have to buy an additional switch.Q1) Is it true that at any point in time...
Hello all,For a while I have been thinking about posing this question. It is about the forum and what it does to our business opportunities. I have noted that many end-users have found the way to this forum. They are using it to solve problems for wh...
Hi,The cisco 4503 has one blade with gbic's SX (fiber), The 2950 EI has also a GBIC SX (fiber). How do I configure both catalyst the communicate with each other?If I have more 2950 EI how do I configure them?thx,Marc
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |