Is GLBP SSO-aware yet? If so.. please provide link and/or version information. If it isn't SSO-aware yet.. any timetable? Thanks in advance.- Matt
Is GLBP SSO-aware yet? If so.. please provide link and/or version information. If it isn't SSO-aware yet.. any timetable? Thanks in advance.- Matt
How would I set up an internet router for say 50 pc's. Do I need to use nat, from what I can remember, do you use the nat overload command ??please helpCarl
Can you provide me with a sample configuration for rate limiting on the 6513 IOS?For example, rate limit a 100Mbps interface to 50Mbps.Thanks,Ben
I am wanting to know if theres a diference between port group in the older switches such as a 2900xl and an etherchannel. Other than the fact that the older switches dont support Port Aggregation Protocol. Are etherchannel and port group exactlly th...
I have just bought 4 new 3560 switches. I setup 3 of them with the CLI but I setup the 4th one thru the GUI. Now when I browse to the switches by IP, I get a different screen on the ones I configured with the CLI vs the GUI configured switch.On the...
HiI am experiencing a problem, I have a 1000 sx module that is recognised by the switch but when I issue the nonegotiate command it seems to ignore. If I admin shutdown then enable I get this message,cpd_port_enable: port 24 xcvr_enable_link: FALSE %...
In my network, I hav got 1 No. Cisco 6509 Sup2 with Redundant Sup2 & p/s,HSRP enabled with 23 VLAN's created on L3 card, backplane traffic utilization is not exceeding more than 10%, & 22 Nos. Cisco 2950-24T, now i wanted to put a standby switch in d...
Hi I have this problem with Cisco 3550 switches in the network. There are a total of 3 Cisco 3550 Switches and all of them have reloaded by themselves. The strange thing is all of them have rebooted after exactly 497 days.IOS version on the switch is...
I've got VLAN's setup on a core switch. I need to propogate these VLANS to my edge switches and I know how to do this by setting them up in client mode. However these switches have already existing VLANs setup with ports assigned. Is there a way to d...
Hi,I've just started work for a company - they have no network documentation or knowledge of their current set-up whatsoever.For the LAN in the office they have Cisco Catalyst WS-C3524-XL switches. But it doesn't seem like these are even configured ...
Can anyone show me a config about having 2 routers , 1 being redundant in case the other goes down !!
please help with the above question. This product is EoS therefore I cannot find anything on Cisco website. Thank you very much.
Dear All,Kindly conform me that wheather the Cisco 2950T-48 SI switch support stacking feature or not. If yes then how meny switch can be stack together. Is it require stacking cable. Also conform me the MAC address and the VLAN supported by this swi...
I have a switch at a remote location that has been in place for sometime that for some reason was never assigned an ip address. CDP is enabled, it is directly connected to a router. Here's the show cdp nei detail output... -------------------------...
HiI am confusing about distance 255 command and order of them. I have tried to read IOS IP Routing Reference and IP Routing Protocol Independent Feature but still not clearly. Could anyone please correct me?1) What is the distance 255 command means? ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |