07-09-2004 07:53 AM - edited 03-02-2019 04:58 PM
My network is as follows.
7206 and 3620 routers connected to a 3524 (port 1 & 24 respectively) using dot1q trunks.
In the 3620 I have configured 2 sub-interfaces (vlan1 and 200).
In the 7206 I have configured 1 sub-interface (vlan 200). And use the interface fe 0/0 for vlan 1.
In 7206 (sub-interface vl200) I have configured:
"rate-limit output 1024000 192000 384000 ..."
and in 3620 (also sub-interface vl200) exactly the same
When I do and extended ping (using vlan 200) from 7206 to 3620 many packets are dropped.
When I do the same (using vlan 1 with rate-limits configured), no packets are dropped.
Can anyone please explain why?
Thanks Fernando
07-09-2004 08:16 AM
Hello Fernando,
is there any other traffic being transmitted on VLAN 200 ? Can you post the configurations of both routers ?
Regards,
Georg
07-09-2004 08:41 AM
7206
interface FastEthernet0/0
description Cisco 3524 TrunkLink
ip address ????????? 255.255.255.248
full-duplex
interface FastEthernet0/0.102
encapsulation dot1Q 102
ip address ???????????? 255.255.255.252
no ip redirects
interface FastEthernet0/0.104
encapsulation dot1Q 104
ip address ?????????????? 255.255.255.252
no ip redirects
interface FastEthernet0/0.200
description Cisco 3620
encapsulation dot1Q 200
ip address ???????????.165 255.255.255.252
rate-limit output 1024000 192000 384000 conform- action transmit exceed-action drop
no ip redirects
interface Serial1/0:1
ip address ?????????????? 255.255.255.252
interface Serial1/4:1
ip address ?????????????? 255.255.255.252
router eigrp ?????
redistribute connected
redistribute static route-map STATIC_TO_EIGRP
passive-interface FastEthernet0/0.200
passive-interface Serial1/0:1
passive-interface Serial1/4:1
passive-interface Loopback1
network ??????????????
no auto-summary
no eigrp log-neighbor-changes
3620
interface FastEthernet1/0
description Interligacao3524
no ip address
speed 100
full-duplex
no cdp enable
interface FastEthernet1/0.1
description ManagementVLAN
encapsulation dot1Q 1 native
ip address ??????????????? 255.255.255.248
no ip redirects
no cdp enable
interface FastEthernet1/0.122
encapsulation dot1Q 122
ip address ??????????????? 255.255.255.248
no ip redirects
no cdp enable
interface FastEthernet1/0.123
encapsulation dot1Q 123
ip address ??????????????? 255.255.255.248
no ip redirects
no cdp enable
interface FastEthernet1/0.200
description Interligacao7200
encapsulation dot1Q 200
ip address ??????????.166 255.255.255.252
no ip redirects
rate-limit output 1024000 192000 384000 conform-action transmit exceed-action drop
no cdp enable
router eigrp ????
redistribute connected
redistribute static route-map STATIC_TO_EIGRP
passive-interface FastEthernet1/0
passive-interface FastEthernet1/0.122
passive-interface FastEthernet1/0.123
passive-interface FastEthernet1/0.200
passive-interface Loopback1
network ???????????????
no auto-summary
Thanks
07-09-2004 09:44 AM
Hello,
when you say you are using an exended ping, what options do you use regarding the packet size and the interval ? Also, you are rate-limiting your FastEthernet interfaces to 1-2MB, can you try and see what happens when you increase it to let´s say 10MB ?
Can you also post the output of:
show interfaces rate-limit
Regards,
Georg
07-12-2004 03:26 AM
Hi again,
for the extended ping i use the defaults except for the ping count which i use 1000000.
the rate-limiting value is because we have some clients behind that network that share 1mb.
remember that these settings i have also tested with vlan1 and didn´t have the same problem.
at this time i cannot paste the rate-limiting output because its deactivated in the 7206 and we are doing a input/output rate-limiting in the 3620 on vlan1.
thanks
regards
fernando
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide