Routers - Small Business

Hi ... i really tried a lot of combinations to connect my osx high sierra to a vpn on cisco rv042g small business router, but no success   Anyone may tell me a solution or example configurations to learn?   I want: - to use a built in osx vpn client ...

I am having difficulty getting port forwarding to work on my RV345P Router to be able to access security cameras remotely.  I have enabled the correct ports via port forwarding to the network device that is used for the security cameras.  When I chec...

I have an old WRVS4400N that I've been trying to set up to a pre-existing LAN, I got it to connect but my connection speed drops from 150Mbps average to 26Mbps across the entire network (LAN & WAN). I tried messing with the settings, upgrading the fi...

I have never operated a Cisco 1720 router.   Last day it was the first time to operate 1720 router. But I couldn't find a specific command, 'show env'. Does the 1720 router originally not support 'show env' command?

Hello, i have a problem with network based on two gates.   Gate 1 is a ISP router with DHCP and access to internet, IP of device: 192.168.0.1/24 Gate 2 is a another ISP access modem connecting directly to VPN of my company, IP of device: 192.168.225....

Hi there,   here my situation: * My company-LAN use a RV320 * RV320 "gateway to gateway" VPN-tunnel to a third-party VPN: works fine (ping, ssh via company-LAN to the third-party machines) * RV320 "OpenVPN-Server" is up and running * RV320 "OpenVPN-A...

This router was updated some time ago. Since that time access to the gui has failed. I tried factory reset and I believe something occurred but not sure what as I still can't gain access. I tried from the wan side also, no joy.  What I think happened...

My customer has a RV320 at two locations with both dual WAN's (in Fallback mode) via different Service Providers (see the attached configuration). VPN between the two locations works fine but we have tried all possible settings to setup the Fallback ...

I have a Cisco RV320 that uses a public IP of x.x.x.181. Our ISP has also given us a block of 16 public IP's using a gateway of x.x.x.145 with usable IP's of x.x.x.146-159. I need to be able to pass these public IP's without NAT'ing to an internal se...

Is et up a new RV345 today and allw as good until a reboot.  Afterward I would just get Web Login Disabled.  All I dd during setup was ad some VLANs, changed all port to use the 192.168.75.1 vlan, enabled intervlan routing, created a VPN and set up s...

I just got a RV130 and setting up the VPNs   I followed the how-to from this link: https://community.cisco.com/t5/small-business-support-documents/configuration-of-an-ipsec-vpn-server-on-rv130-and-rv130w/ta-p/3172473 And the video from this link: htt...

The network setup is as follows:   One Cisco RV180 at site one plugs into a gigabit fiber modem on its wan port. This network operates on 192.168.0.x.   The other Cisco RV180 at site two also plugs into a gigabit fiber modem on it's wan port. This ne...

I am seeing a new log message that is repeating every 30 minutes.     charon: 11[KNL] creating roam job due to route change   I have no VPNs setup on this router.  There has not been any recent changes on my RV340 router.  I am running firmware versi...

Hey there, ( I apologize if this is the wrong group) We  have a Cisco 1941 on site that I don't have admin rights to.  The other night we were hit by lightning and the house went dark.  When the power came back the router came back on but there are n...