Routers - Small Business

HI,I have a RV042G (router), SG200-26 (switch)ISP Modem on cable have dual wan static ip Switch have 4 Vlanvlan1 defaultvlan2 networkAvlan3 networkBvlan5 Modemport (1UP,2T) management portport 2-12 (2UP) Network Aport 13 (5UP,2T,3T) wan cable plugpor...

The RV320 I've just put into production is being run in a default block for all outgoing connections with explicit allow rules for all the ports that the network users are allowed to use. This has resulted in all 50 of the allowed access rules being ...

Hello,I just bought an RV320, as stated in the admin guide on page 91, the Cisco Easy VPN client should be on the product CD. The client is missing on the CD i have received Would you be so kind to either send me a download-link ór send me the client...

 We have a RV320 router. To our knowledge, we use it with out-of-the-box setings, all clients get the LAN ip-address via DHCP from the RV320. The problem is the time it takes for the RV320 to hand out an ip-adress, it takes between 1-2 minutes, both ...

Hi !My RV110W reports wrong SNMP ifSpeed and ifHighSpeed values for eth0, vlan1 and vlan2 ( 10 Mbit/s instead of 100 Mbit/s ) for . This causes my SNMP management software to malfunction ( graphics are capping out flat at 10 Mbits/s ). ifSpeed and if...

I'm attempting to get the Cisco RV320 running FW v1.1.1.19 to work with the AT&T Beam / Sierra Wireless 340U. This AT&T LTE USB modem is listed as supported in the release notes for this version. This is the only AT&T modem supported unfortunately.I ...

I have two RV220W (one is the main router and the other is acting like an access point). The main one [192.168.1.1] is located in our server room so wireless signal from there is very limited. The access point [192.168.1.2] is in the main reception a...

We are experiencing slow internet connection.  RVS4000 V2We have Charter Internet and have plugged in directly to the modem.Up speed is 60+ and down is 4+   However, when checking speed in the network, up is 14 and down is 4.Our modem is no longer su...

I have both Cisco RVS4000 & Linksys RVS4000 routers in Use.I can only find Firmware V 1.4.1.2,I have updated all my CISCO branded Routers.Will this File work with my Linksys Routers as well.  They have V 1.1.14 now.ThanksGreg.

Why is DynDNS.org the only option or dynamic DNS for US based users?  (3322.org is all in Chinese, so I have no idea what they support.)Is there some way to extend this?  I'd like to see support for one or two free dynamic DNS sites.Thanks.J

I have an RV016 router with 2 Fibre WAN connections on it.  I have two internal servers with resources I need available externally.I would like WAN1 to forward port 443 to server 1 and WAN2 to forward port 443 to server 2.It does not appear this is p...

I have a single SSID id setup with around 40 clients connected (combination of laptops and phones), after a reboot all the clients can connect fine wireless-wireless and wired-wireless. However after a couple weeks, with no configuration changes, the...

Can someone please tell me which ISR G2 router support at least 64 VTY Lines. I need to build a Terminal access server for a school. Thanks

I can connect to my rv220w from windows seven with a downgrade of IE11 to IE8.With windows 8 this downgrade is not possible. So is it possible to connect a client from  windows 8 ? How can I do ? thanks for your help 

Hi,I have a RV220W router, WAP4410N access point, and SG300-28P switch - all on the latest firmware.I would like to configure a guest SSID on the WAP4410N but can't seem to get it figured out.What I've done so far is:Create a vlan (let's say 100) on ...