Routers - Small Business

We have a website that is hosted (IIS) on our own server. We had the Cisco RV320 installed two days ago. Since that time we are unable to access the website from the LAN. Everything is fine from the outside world though. This has been working fine fo...

Hello, I would like to ask You if You have same problem as me. I would like to allow PING on RV042 from WAN side only from specific IP address, but when I set the rule, RV042 does not respond on WAN side, because Block WAN Request is Enabled.BUT! Wh...

Hi,I have a Cisco SRP 526W Router and I wanted to set up UMTS Backup. Unfortunatelly my Voice-Internet provider only have a USB-UMTS Stick model which is not supported by Cisco SRP500, Huawei K3765. I know it´s compatible with many old Huawei USB-Sti...

Hi,I recently had fibre installed whereas previously I was using ADSL.  I have been using an RV220W switch on my internal network for many months and that worked just fine in conjunction with a Zyxel modem in bridging mode with the RV220W authenticat...

I'm helping a client who has an RV110W router connected to Charter Cable Modem (50Mbps). Router connects to a Cisco switch, to patch panel, to devices. He has Cisco IP Phones, model 303.Every 30 seconds, pinging the router from a wired desktop, pings...

Have a SRP521W.  Router runs fine.  External port scans show port 22 open even though SPI firewall is enabled and remote management is disabled.  Need assistance disabling port 22 on the WAN to meet a compliance issue.

Dear all - this is a bit a of concept question. But it seems an obvious and generic requirement - but I can't find a nice, neat and simple solution? Or maybe I can't see the forest for the trees? Help/pointers would be appreciated - the first bit is ...

We just bought the RV042 and need to understand how to config the belowI have 2 Internet Connection and connected to 2 WAN Ports and now I want few computers to get the Internet connection from WAN 1 and Few Computers from WAN 2.. How do I setup this...

We just bought the RV042 and need to understand how to config the belowI have 2 Internet Connection and connected to 2 WAN Ports and now I want few computers to get the Internet connection from WAN 1 and Few Computers from WAN 2.. How do I setup this...

Hi All,This week i bought a RV180 to replace a router which is delivered by a Fiber To The Home provider in the Netherlands (KPN)In the Netherlands our FTU sends out 3 Vlans, 6 for internet, 4 for TV and 7 for telephone.The provider uses PPPoE to con...

I cannot connect to the SR 520 Router.  The device's IP Address is 192.168.0.1 and shows up as the default gateway for client computers.  I can ping the SR 520 and get replies to my pings.  However, I can't telnet or ssh to the router, it tries to co...

WAN1-address 10.0.0.140, 255.255.255.0, MAC xx.xx.xx.xx.xx.25LAN1-adress 192.168.2.140, 255.255.255.0, MAC xx.xx.xx.xx.xx.24When both interfaces are connected to the SAME physical network, the ip-address 10.0.0.140 resolves to MAC-address xx.24 while...

Hi ,I would like your feedback on what product to invest in.I am currently managing the network infrastructure for a small traveling company. The amount of people accessing the Internet during business hrs are between 30-40 active users, at peak time...

Hi guys. I'm trying to setup a site-to-site IPSEC tunnel between an ISA500 and Cisco 887. I've configured the tunnel at each end, and it seems to be up. Running "show crypto engine connections active" on the 800 and the decrypt count goes up when I t...