Routers - Small Business

Hello, we have in our company Dual WAN router RV042 with NAT 1:N and on LAN we have VoIP PBX WELL mPBX-100. It was working for about 3 weeks, but yesterday I was upgrade firmware from 4.0.0.07 to 4.0.4.02 and after upgrade don't work VoIP PBX. SIP tr...

Hi all.I just configured a RV016 v3 and it's ignoring my VPN connections and its routes.All the tunnels configured are connected, some of them run fine, but it's not constant.When I run a tracert to my other site it returns all the hops between them ...

I recently bought an RV220W. I run several game servers from a server on my network. With the new router, I can connect to the server with the LAN IP, of course, but I can not connect using the internet IP of the server. I believe it is properly port...

Dear All,I successfully set up 4 connections between the RV220W and 4 third party routers. Ping, etc. works fine.However now I found out that the connection can only be established by the third party routers. When I try to initiate the connection eit...

hey everyone, a client is thinking of putting in a srp527w.they get assigned a static ip on the adsl interface (165.228.204.x), and then have been assigned another block(203.39.183.x/29).how can i have it so that i am able to forward individual ports...

Hello all,I'm having difficulty setting up a manual key VPN between (2) RV082 routers.  I've set up the VPN per the instructions, but it doesn't seem to function.  I've sniffed the WAN port with Wireshark during pings, and what I see looks like the p...

I recently purchased the RV220W to upgrade by good, but aging RV042. I'm running the most recent firmware (1.0.2.4 as of this writing) and have noticed this router reboots daily. I'm guessing it's locking up and rebooting as it occurs as different ti...

Hi, my I have an rv042 subnet 192.168.1.0 gateway 192.168.1.1 I also have a tg585v7 provided by my ISP. This has subnet 192.168.2.0 and gateway ip 192.168.2.1When I connect the tg585 to wan1 with the rv042 set to obtain ip automatically and dual wan ...

I have two plant automation networks lets say A/24 and B/24 without comm between them, and as per the menufacturers of the atutomation controllers, the routers between them have to be able to direct broadcast.How to do it with a RVS4000?

RV220W is at firmware v1.0.2.4 From: Administration / Management Interface / Web Accesss I have configured remote Management:Remote Management [x] EnabledAccess Type: All IP addressesPort Number: 8888Remote SNTP  [  ] not enabledFrom within the LAN s...

Hi,I have multiple RV082 routers.  4 have Internet facing WAN ports with Static Public IPs.  The rest are upstream from these routers.  3 of  these 4 routers share the same Public IP (WAN) subnet and gateway.  I can set up static routes using the WAN...

I'm tryng to configure a vpn with a cisco small business pro router, model srp527W-k9-g5But when i try to set the “remote ip”  in Remote traffic selection a I have to set (10.0.0.0) a message said:  “Invalid IP Address Format”If i change the ip and i...

Will a VPN running on the RVS4000 connect up to an iPad running Cisco Anyconnect ?

used to be able to access this secure website (https://campus.dcsdk12.org/icprod/portal/icprod.jsp) prior to a firmware upgrade.  Can no longer access.  On Firmware Version: 3.0.2.01-tm.  Assuming there's some default setting in the firewall?  Any id...

I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port. Can you he...