Working through configuring this wretched device.... firmware 17.9. I have 2 IKEv2 RSA auth site-to-site VPNs using tunnel interfaces to 2 other sites with non-Cisco routers. Everything comes up and is working fine, traffic flows without interruption...
Forum Posts
Hi All,Have an issue configuring a cisco C8200-1N-4Twith IOS-XE 17.06.06a for local console login with no external servers. I have use the following commands but still can not authenticate. aaa new-model!!aaa authentication login default localaaa aut...
Hi,We have a need to use the same subnets as OSPF routing/transit networks at muti locations in the the OSPF area. see diagram.BBU3 will have a loopback of 10.0.0.3/32, and BBU4 will have loopback of 10.0.0.4/32. We don't care the reachability of os...
I want to write syslogs to flash. But The only document I found online is: https://www.cisco.com/c/en/us/support/docs/voice/telephony-signaling/212102-Configure-Persistent-Logging-on-Cisco-IO.html Which doesn't say much about what options are availab...
All IPs, AS numbers, OSPF areas, etc., have been sanitized for this post. None are currently in production.- I have a subnet at a remote network that I need to extend from a /24 to a /23.- We have two circuits at this site: a primary MPLS going to ou...
Hi, starting something new here and seem to be having an issue. My FPR1010 is set in PPPoE Mode and obtains a Static WAN IP as its GW and I also have a block of 8 Static WAN IP’s (6 usable). I was trying to assign a DDWRT router to an Interface on th...
Hi ! I have a multicast setup in my network using PIM-ASM. For some reason a router in my network stopped responding to IGMP requests. Although the show commands for IGMP showed everything works. Has anyone experienced the same thing? I’m planning to...
Resolved! Redistribution
Hello, I'm confused about something and would appreciate any guidance or assistance.In my topology, each PE router is located in a different AS and is directly connected to the CE router. Each AS is running iBGP alongside an IGP. VRFs and MP-BGP have...
Hello All,I am trying to understand how ospf works over ipsec tunnel as OSPF used multicast to discover neighbourship and ipsec does not support OSPF.some vendors now directly support OSPF Over ipsec with NBMA network and i am trying to understand ho...
hi im a student..i cannot ping pc A to web server..why??i already allow the firewall but its still same..can someone tech me how to solve it?
RP/0/RP0/CPU0:TEST-A#sh policy-map interface twentyFiveGigE 0/0/0/33Mon May 5 16:24:49.403 JSTTwentyFiveGigE0/0/0/33 input: IN-CORE-QOS-POLICYClass IN-CONTROL-SIGNALINGClassification statistics (packets/bytes) (rate - kbps)Matched : 92749145131/16572...
Hello, We are running the 4G LTE base module for IR1101 with default configuration. When I start up the switch with default configuration everything works perfectly with profile being active and IP address is recieved. We are running a private APN. I...
I have a nexus switch 93180YC-EX.I'm getting below warning syslog message:%TAHUSD-SLOT1-4-BUFFER_THRESHOLD_EXCEEDED: Module 1 Instance 0 Pool-group buffer 90 percent threshold is exceeded! (message repeated 1 time)When I checked the resources usage, ...
Resolved! C1111-8P booting into ROM
I am new to this Cisco Router. I bought this router with the below specs when I turn on the router it is going straight into "ROMMON" Mode how do load the new firmware. Your help will be greatly appreciated.General InformationManufacturer: Cisco Syst...
If you are studying IS-IS, you might note that we are setting the last 8 bit to (00). This last bit is called the NSEL, but why are we setting it to zero? Well, when configuring NSAP addresses for routing purposes (especially with IS-IS), the NSEL is...
