I am trying to setup a connection to a remote non domain workstation that is behind an unmanaged router.My routes aren't working and any help would be greatly appreciated.The SVI for VLAN 163 in on router 3The gateway for the 92 network is on the unm...
CAN SOMEONE SOLVE MY PKT
I am encountering an issue while attempting to replace the bootflash on an ISR 4431/K9 with MEM-FLSH-16G. Specifically, I have observed two distinct types of MEM-FLSH-16G, differentiated by their serial numbers:Units with serial numbers starting with...
hi all.im trying to upgrade a ir809, but keeps getting this error:VV_SAK_VB01#bundle install flash:ir800-universalk9-bundle.SPA.158-3.M9.binInstalling bundle image: /ir800-universalk9-bundle.SPA.158-3.M9.bin..............................................
Hi, Ive just discovered about the command:ip access-list resequencewhich I think its very handy.Is there a way to suggest or at least know if CISCO is planning the same for PREFIX-LIST?Vlad
Hi, I got this topology here: I got my Windows PC with IP 192.168.10.128 and i have configured it with a static route: Persistent Routes: Network Address Netmask Gateway Address Metric 100.100.100.1 255.255.255.255 192.168.10.130...
Hi All,I m trying to set Destination NAT so that an outside source can send some logs to an inside log collector server via UDP . The translation device in this case is a FMC managed FTD . Please find below the expected flow of the trafficSource IP a...
Hi all,I'm having an issue getting cisco packet tracer to send packets from switch 1 to router 2 to router 1's gateway ip address. I've narrowed the problem down to ip routing within R2. From SW1, I can ping router 2 but cannot pass through R2 and pi...
I set up a C1121-4P router for a friend with int gig0/0/0 facing the ISP with ip address dhcp. int gig0/0/1 192.168.1.1/24. See attached sh run. Vanilla Configuration not much security or complexity. After a power reload the GUI "https://192.168.1.1/...
Dear Community,We have total 5 sites in our network. All 5 sites are inter-connected via BGP in MPLS could.Site A & Site B has only internet link to forward any internet traffic to web.Site C, D & E should use Site B's internet link as Primary Gatewa...
Hello everyone,I have a NCS 540 running IOS-XR 24.2.2 and I'm trying to setup an architecture with a total of five vrf including a "hub" vrf where all routes should be exported to / imported from that I can't seems to get working: routes from one vrf...
Hello,Can you tell me if it is possible to reduce the switchover time of an Xconnect in backup peer mode ?On a router I use xconnect (l2tpv3) to a primary router and backup peer to the secondary router :interface GigabitEthernet0/0/1no ip addressnego...
Hello,I would like to be able to bridge two ports in the same xconnect domain. I can't do it and wonder if it is possible to do it ?I tried the configuration below on an ASR 1000 :interface GigabitEthernet0/0/0 no ip address negotiation auto cdp e...
Hi,I am having some problems with ISDN lines being utilised when I don't want them to be!I have a 3640 (IOS ver 12.2(13)T1) router with 128k point-to-point cell-frame lines to about 30 branch routers (mostly 1603's with some 1700's and a couple of 26...
Hi,we have a running dmvpn hub spoke environment with cert based authentication of the routers. So far, so good. Now some of the branch offices routers are also configured for cube functionality and for that to work we needed to install a public sign...
