Resolved! Scheduled reload
Hi. Quick one. If we schedule a reload, would all the siwtches in the stack reload? So if we add the command "Reload in 23:00" would that restart all switches in stack? Thank you
Hi. Quick one. If we schedule a reload, would all the siwtches in the stack reload? So if we add the command "Reload in 23:00" would that restart all switches in stack? Thank you
Hi experts, I am in trouble with PfRv3 loadbalancing implementation. Given the three independent cellular uplink, with three DMVPN cloud in one spoke router. What bandwidth parameter should I apply under the cellular interfaces on the branch devic...
What is special in ISR router ? what are the special feature it has compare to normal router ?
Hi everyone, So recently our company has purchased a Cisco C881. I've loaded CP Express on it just in case because I'm still learning to work with the CLI. I've configured a static WAN interface (fixed speed at 100Mbps Full Duplex) just like on our ...
Hi, CSC: Quick question regarding an ISR Performance and its Performance License. For example, if we look at ISR4321, the DS says this box has 2 expected performance levels: 50Mbps and 100Mbps.Are these levels enforced in any fashion, meaning that th...
Ping same range red Router#ping 10.195.1.59 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.195.1.59, timeout is 2 seconds:.....Success rate is 0 percent (0/5)Router#ping 10.195.1.58 Type escape sequence to abort.Sending 5, 100-by...
We just experienced this the bug that cause our ASR 1002-X to reload randomly and the last reload reason was Watchdog. What causes this and what version of code is recommended to fix this. The bug ID didn't show this version as having this bug, b...
Hi all, I have a simple topology, where R1 is connected to R2 with a BGP session between them. On R1, I have a static route: 10.0.130.0 255.255.255.0 192.168.0.1 I just want send to R2 only prefixes 10.0.130.18/32 and 10.0.130.58/32, not all 10.0.13...
Hi, How to troubleshoot the scenario where the bandwidth of a link is upgraded to 1MB from 512 kb but the throughput over the upgraded link is not getting beyond 500 kb when load is applied on the link. Example: ======= Cisco 1812 CE: 25.2.1.1 P...
Hi, I'm looking at this command as it seems useful. however, what do others recommend for maxas counts? I am thinking of 12 for an edge router connected to internet. The default route is in place to catch anything higher. Based on some current calcul...
Hello, We are using QinQ in a classical way to exchange customer vlans between two switches ( catalyst 3750G-12S-E ). On site A , a customer has 3 ports configured in dot1q-tunnel Port 1 : Tagged traffic from vlan 500 to vlan 510 Port 2 : Untagged...
Hey all, So I'm trying to nat two services over an IP SEC tunnel. <Internet> -----> <Public IP's> -----> <Router 1> -----> <tun interface> -----> <Internet> -----> <router 2> router 1 config ip nat inside source route-map NoNat interface Gigab...
Looking for some assistance in my BGP configuration. I have a peer (172.26.10.10) not coming up. I have a small porition of the config, let me know if you need more. I've also posted the logs of what i'm getting when i bring up gi0/0/0.129. I have tw...
Hi, we have L3 switch/routers in 4 sites and were wondering if we could configure BGP between routers without the ISP participating. Static routes have been configured between the routers of each site. What is the best way of getting this configured?...
I am new to routing and switching. can someone please tell me what is the purpose of serial interface on a router and is it used in latest routers?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
05-13-2025 03:49 AM | ||
05-12-2025 03:28 PM | ||
05-09-2025 02:25 PM | ||
05-05-2025 11:47 PM |
User | Count |
---|---|
13 | |
9 | |
5 | |
4 | |
4 |