Hi, Does anyone know how to get ADSL working through a c1117? We upgraded to one from a 1841 so I just copied the config over but the dialer wont get a IP address from the ISP. If I look at the dialer int on the 1841 it has a public ip assigned to it...
Forum Posts
Hi All, am using the following topology for BGP testing , but am not able to establish bgp neighborships between R1/R3 and R2/R4. The sample config/output is mentioned below:- ****************************************************** R1#show ip bg...
Dear @I am experiencing an issue with VXLAN static ingress replication on a pair of Nexus switches running NX-OS 7.0(3)I7(2). The setup consists of two leaf switches (NX-6 and NX-7), where VLAN 100 is mapped to VNI 5000 on both switches. Each switch...
hello,I am facing with a big problem in my cisco switchI have cisco 6880 switch with an OSPF link to cisco switchesIt has been working fine for years and all of a suden the process went down, and is stuck in EXCHANGE/EXSTART statesI have another OSPF...
Hello.I currently just got a Cisco 2821 with CallManager(8.6) installed and IOS(15.1M) and ADVENTERPRISE installed. It has 512MB of DRAM and 256MB of Compact Flash memory. This device will solely be used for VoIP.I was wondering if it would be enough...
Hi,I'm looking for a similar command in IOS to the "alias" command for PIX. I have a setup where my internal clients need to reach a web server in the DMZ. The DNS response is the outside (official) IP address of the web server. I would like the Rout...
Resolved! IS-IS Single topology vs Multitopology
Hi Guys, Can anyone explain to me in simple terms what the difference is between IS-IS single topology and multitopology? The documents available online are very confusing and conflicting, even cisco's. I have tried to simulate both on my labs and ca...
Hiany Free NMS software on linux of windows server Can monitor BGP session on Cisco routersFor example uptime prefix numbers and prefix addresesses ?for example X.X.X.X/24Y.Y.Y.Y/21How can Do this ??? by snmp ???
Hello.I've been reading the Datasheet for the Cisco 2821, and it says that the PDVM2-64 can be used on it. However, there are 3 PDVM slots available on the 2821. I was wondering if there is a limit as to how many of the PDVM2-64 can be put in the rou...
Resolved! standard acl issue
Hi Team,Can you please help on one acl issue ?I have two devices connected A --- B (ios/ios-xe, issue on both) , having bgp neighbor ship. Device A is advertising 2.2.0.0/16 and 12.12.12.0/24 prefixes to device B using bgp. Device B has route-map app...
What is the throughput of the ISR4431-SEC/K9? We also want you to teach us about the standard bundled licenses.
Hello all,I'm trying to determine the exact order of operations a router takes when you run mpls ip on the router, specifically when/how the router builds the LFIB table.The first step I have is that the router takes all the routes in the RIB and ass...
Hello, We have couple of Cisco ASR-920-4SZ routers, which we are currently using to connect to the Internet. We are planning to upgrade the access speed to 5Gbps which will require us to use one of the 10G ports. We did purchase the appropriate lice...
I need to upgrade my C9300-48P from IOS XE 16.12.04 (Gibraltar) to 17.9.6a (Cupertino). sh versionCisco IOS XE Software, Version 16.12.04Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.12.4, RELEASE SOFTWARE (fc5...
Hi all!I have a couple of questions regarding ospf route redistribution:1. How can I determine which ospf routers are being redistribute into other protocols? First, I thought show ip route would give me the answer, but apparently not. For example,...
