hi, I am configuring the Catalyst 8300 and install the sfp module GLC-TE in interface G0/0/4. but i don't configure the speed 100M in this interface, how can I configure to
Forum Posts
CISCO-IPMROUTE-MIB is based on RFC 2932: IPv4 Multicast Routing MIB. RFC 2932 is obsoleted by RFC 5132: IP Multicast MIB. So, if a device supports RFC 5132 then it is not compatible with CISCO-IPMROUTE-MIB.Is there a CISCO-IPMROUTE-MIB(mainly interes...
We are planning to deploy a Cisco C1121 router within a closed network environment that does not have internet access.We have purchased the SEC license (SL-1K-4P-SEC-SV=) along with the device. Could you please confirm whether activation of this lice...
I'm working on a project to enable Internet failover for any of our offices (see diagram). We have four paths to the Internet and three pairs of firewalls. So far my failover configuration is good for the remote offices. It was challenging but we wen...
Hello Everybody, I am trying to create a network WAN on my labo and I met a little problem that when I ping the next hope, one packet of two are lost. Type of connectivity: Fiber Network: Ipv4 Class public type of route: default route You will find...
Hello,Can someone please help me shed some light on AF classes?RFC2597 does not seem to dictate prioritized treatment of one class over any of the others:"This memo does not specify that any particular relationship hold between AF PHB groups and othe...
Hello,I'm currently studying for the ENCOR exam and came across the topic GRE over IPsec in Tunnel Mode / IPsec over GRE.The OCG describes GRE over IPsec in tunnel mode as follows:"In [GRE over IPsec] tunnel mode, the original packet is encapsulated ...
Hi everyone,I’m facing an issue with my Cisco router where the internet speed is much slower than expected, even though my internet plan is high-speed. The speeds fluctuate and sometimes drop significantly, making it difficult to browse or stream con...
Friends, I'm on my second RV345P and have a public facing range and trying to forward one IP from that public facing range to a LAN address. When I try to resolve to the public facing IP, I'm simply taken to the RV345 login screen. Traffic from the W...
Resolved! Redistribute EIGRP to OSPF
I need some clarification on this, I redistributed routes from EIGRP to OSPF through area 45 and it works fine. My question is, is it a best practice to redistribute into a non-backbone area rather than the backbone area?
C8300-1N1S-6T／DNA-C-T0-A-3YI've tied it to SAVA and ordered it, but the C8000-HSEC is visible in SAVA.DNA-C-T0-A-3Y not visible in SAVA I think you can see C9300-DNA-E-24S-3Y etc. within SA.DNA-C-T0-A-3Y is The license(s) were provisionedAre model nu...
I find a problem when I want to configure a interface vlan on C8300 . Any solution
Resolved! OSPFV3 With IV4 Families
Hi cisco community,Please bare with me but i believe i am missing something in my attempting conversion to ospfv3/w IPV4. Recently, we received a new security device that does not support SHA over OSPFV2. Our network does not have IPV6 present intern...
With the help of Paresh here in these forums I got QOS working, I think, but would like a good book to explain things in easy to understand format.The articles and white papers on the Cisco site are great, except they often leave me wondering why one...
I have 4510 cisco switch. One of the switch port was down last nigt for few time and now its up. So my customer is asking me how long it is up. i mean its up time how long. How can i get this information with out syslog server.
