I'm working on a SD-WAN lab on EVE-NG vm and I'm trying to access vManage GUI but it keeps saying "this site can't be reached". It worked before but now it just can't. The request nms all status shows that application server is running. I'm working o...
Forum Posts
Hi All, I am configuring SD-WAN/SD-Access independent domain pairwise integration. I have configured a port-channel with sub-interfaces per VN on an 8500 cEdge via CLI add-on Template, connecting to a Fusion switch. I am enabling CTS and found the 'C...
Hi, I am currently using vEdge version 20.3.1. I managed to onboard vEdge to vManage and did not create CSR on vEdge. As shown in the steos below I successfully onboarded vEdge to vManage. I would like to confirm if there is a need to generate CSR on...
Hi All We have constructed an On-Prem Viptela Lab using Viptela version 18.4 using VMware with ESXi 6.5. I know that as per Cisco Docs the supported versions are 5.5 and 6.0 but have found many blogs where people have tested the Lab without any iss...
Resolved! vManage dynamic list of nat rules
Hello. I have a challenge to create single feature template for vEdge routers where I can dynamicaly define static nat rules. Each vEdge will have different amount of hosts to be NATed. Any ideas or suggestions? Template per device is bad option. Tha...
Hello, I'd like to get more information about the effect of the 'capability vrf-lite' command on Cisco SD-WAN Edge devices. I'm using IOS-XE Version 17.3.3. I tried some things in the lab to test what happens if the command is there and when it is no...
Hi ,I added a router into pnp site and we tried to synchronised with vManage. All parameters was add to pnp, the vManage when sync, it hears the device, it is present , but when terminated the sync we not see.what do I have do for add the edge router...
HI I am using vManage image 20.6.3 and following all the steps mentioned in how to guide available EVE NG official sitehttps://www.eve-ng.net/index.php/documentation/howtos/howto-add-cisco-viptela-images-set/i am using the following commands for addi...
Hello everybody,out customer has a SD-WAN router:cisco C1111X-8P (1RU) processor with 1971490K/6147K bytes of memoryrunning IOS Version 17.6.3a.Our monitoning generated an alalm for high CPU load.The command 'sh process cpu sorted' shows small values...
vManage 20.3.4.1 POST/dataservice/template/device/cliAPI was successful.We upgraded vManage 20.6.5.5.After update we can see below response from vManage.{"error":{"type":"error","message":"Reserved variable","details":"chassis-number is a reserved va...
We have plenty of vEdge devices in the network; we are starting to convert them to cEdge devices. This is being done remotely. Converting the device to IOS-XE is relatively easy, and the process through vManage works well. It's when that process is d...
I have built a few SDWAN Viptela labs on hardware and software and had a number of issues with creating certificates mainly on the 3 controllers.After having to rebuild a lab again for similar reasons I have run into the same problem. What I have not...
Hi,If I need to deploy 15000 branch offices to a Hub/data center location how much controller is required and how do I manage segmentation? I need to know the design part.
Hello, I would like to understand how we can change system ip of the router. We are using cedge and during one of the change, device ip did not get reflected. would some one suggest what is best way to proceed further. cedge: ISR1100 and ISR4K ser...
Hello. We have the following Meraki Setup.One MX84 in office and 2 VMX 100 in 2 AWS VPCs.The User in office (With MX84) can access service1 and service2 and the 2 services can access each other without any issues.However recently there is something w...
