Hi there, In a dCLoud Lab running SDWAN solution 20.12 I have added a new C8000v and I would like it to join the fabric. I ran the Workflow => Quick Connect and I have downloaded the bootstrap configuration : Configuration => Devices => Generate Boot...
Forum Posts
Hi, VBond and vEdge login issue, it's not accepting default password it says login incorrect doneMounting pseudo filesystems...Setting up hotplug...Mounting filesystems...Setting hostname...Configuring kernel parameters...Configuring network interfa...
Hi all, is it possible to filter ospf routes. For example, cedge i forming ospf neighbor to other core device that is advertisine some netoworks and default route. I want only to accept def route and send via omp to remote branch. I know I can create...
So, I was practicing TLOC extension at my SD-WAN lab on EVE-NG and I spent around 4 hour to troubleshoot this strange issue. The issue is directly connected subinterface cannot ping each other. They are both connected to GigabitEthernet4 physical int...
Hi experts. I have newly deployed an SDWAN environment.The controllers are all version 20.16.1The edge devices use C8000v 17.6.1, and there are 2 C8000v in the network.All controllers and edge devices are in the same LAN.The edge devices can be regi...
Hello,I have a network where I have configured a DC site and a branch site. I have configured a firewall in DC site where I could forward traffic through it to the internet. I'm able to access internet through a static route I have configured in serv...
hii have cisco router 8200lit in controller mode but when i try to config vpn 0 i get "syntax error: unknown command" what i miising?regards aharon
Hello, I am currently doing an SD-WAN lab with cat 8k 17.15.01a in a controller mode , in Viptela Devices i could go to vshell and perform linux commands , also there been a useful tools in the Viptela OS like tcpdump & iperf , are these tools still ...
Hello colleagues! Got an issue with C8Kv and some firewalls in "cluster".There is a typical topology when you have 2 NGFW in a cluster mode (they share all settings between nodes) and 2 C8Kv like "behind", it's all in a cloud's provider infra. I can ...
I have two SD-WAN routers in my office and I would like to establish a Tunnel Session with them.The WAN IP of each SD-WAN Router is set to Private IP and NATed to the same Global IP by the FW.Can two SD-WAN routers with the same Global IP establish a...
Hello All, I need to know if we can configure Q-in-Q VLAN Tunnels on [ SD-WAN ] Cedges 4000 & 8000 or not Commands dot1q tunneling ethertype 0x9100 encapsulation dot1q 100 second-dot1q 200 pppoe enable group vpn1
Hello all,I was studying for ENSDWI exam and doing some labs. I came across this strange issue where BFD connection is not forming between MPLS and MPLS connections but forms with biz-internet colors. I will try to break down the scenario, issue and ...
Dear Team,It looks like we can onboard our cEdges router into our CML 2.8 LAB without using the PnP or Smart account after version 20.xThe problem i am having is the following: I have successfully imported the Chassis number and Serial number from my...
Resolved! Using SD-WAN 20.15.1 in CML 2.8
Dear All,I need your help to understand something. When I ran the automated script to install SD-WAN in CML 2.8, everything works as expected (https://github.com/cisco-open/sdwan-lab-deployment-tool/).When I decide to install manually each components...
Hello comrades! Unfortunately I would like to raise the topic about NGFW-SDwan integration one more time, because the dipper I dig in the more confused unga-banga it turns.The original topic was https://community.cisco.com/t5/sd-wan-and-cloud-network...
